What it means
Maytag prints FAE5 or F10E5 as “Potential Cause: Diverter Leak.” Check for leaks under the dishwasher, make sure the water connections are secure, press Cancel twice and try a new cycle. If the error returns, schedule service.
Maytag dishwasher FAE5 / Water and drain
Maytag prints FAE5 or F10E5 as “Potential Cause: Diverter Leak.” Check for leaks under the dishwasher, make sure the water connections are secure, press Cancel twice and try a new cycle. If the error returns, schedule service.
Also printed as FAE5
Maytag prints FAE5 or F10E5 as “Potential Cause: Diverter Leak.” Check for leaks under the dishwasher, make sure the water connections are secure, press Cancel twice and try a new cycle. If the error returns, schedule service.
Switch off power and the water supply before opening anything, and wipe up spills so nobody slips.
FAE5 returns after the leak check and Cancel twice.
Your Maytag to-do list, saved here on this device

Check for water on the floor or in the base, since the cause line says leak.

The page says this explicitly. If a fitting is wet, turn the water off and tell us.

This is the page’s reset for FAE5, in place of the power cycle used on most other codes.

Start one cycle and see whether FAE5 returns.

Ten flashes, a pause, then five flashes spells F10E5. [1]
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak.
Read the definitionThe ten-pause-five flashing page and the error code page carry the same text: diverter leak, the four steps, and service if the error returns.
Read the supporting manualFAE4 or F10E4 is a diverter valve error, and its only step is cycle power. FAE5 swaps that for a leak check and Cancel twice.
Read the supporting manualF8E4 is water detected in the drip tray: empty the tray, check connections and the float switch. FAE5 names the diverter.
Read the supporting manualStop the dishwasher and turn the water off if you see a steady leak. Dry the floor to protect it.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12607 / PH 12607 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12637 / PH 12637 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 15080 / PH 15080 (dishwasher)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-06-15; PH 12632 / PH 12632 (dishwasher)
Maytag's Product Help names no model range for this code. The retailer copy of the Maytag dishwasher instructions (W10401489A) prints no F-E codes; its troubleshooting table is cited only where noted. Sources: Product Help PH 12607 and PH 12637, with the FAE4 and F8E4 pages.
Maytag prescribes it for FAE5 in place of the 30-second power cycle used on most other dishwasher codes. After the leak and connection check, press Cancel twice and start a new cycle.
The cause line says diverter leak. The page also asks you to check for leaks under the dishwasher and to make sure every water connection is secure, so look at the connections as well as the diverter.
Yes. The error code page and the ten-flash pattern page both carry the same text under the two names, so either spelling on your dishwasher points to this entry.
Not while water is visibly leaking. Turn off the water, dry the floor and book a visit. If nothing is leaking and the code clears after Cancel twice, one test cycle is reasonable.
Maytag codes, symptoms, parts and service
F1E1 on a Maytag dishwasher is explained as “Potential Cause: Control Module.” Cut the power for 30 seconds, then restore it; schedule a visit if the code is still there.
A burnt smell from a Maytag dishwasher is often plastic or food that fell by the heating element. Let the tub cool for at least 30 minutes, clear the debris, and run a rinse or cleaning cycle. A hot tar or petroleum smell on a new dishwasher is the sound-deadening coating and should fade in 4 to 6 weeks.
On a Maytag dishwasher, FAE4 lists a diverter valve error and FAE5 lists a diverter leak. For FAE5, Product Help says to check for leaks under the dishwasher, make sure water connections are secure, press Cancel twice and start a new cycle. FAE4 gets a 30-second power reset.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.