Diagnostics and repair
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
The care journal
Simple habits that keep a Maytag appliance doing its job: lint screens, filters and every part you can reach safely.

Change a Maytag refrigerator water filter twice a year, when its light asks, or sooner if the dispenser slows or the ice shrinks. With no light, Maytag's pages say every 6 months on one page and every 6 to 9 months on another, with an earlier change if flow drops. A clogged filter can stay out in bypass mode, unfiltered, until you fit a new one. [1][2][3]

AquaLift loosens soil with low heat and water; it does not remove everything. On an AquaLift Maytag range, start with a cool, empty, level oven, pour in 2 cups of filtered or distilled water, press AQUALIFT SELF CLEAN then START, allow about 40 minutes, then wipe out the softened soil with a non-scratch sponge. Run it again for stubborn spots, and never use oven cleaners. [1][2][3]

Water at a Maytag dishwasher usually comes from steam at the door vent, suds, a pre-washed or soaked load, an item caught in the door seal, an unlevel or out-of-square tub, or a loose supply or drain connection. Check those first. Water in the drip tray, which goes with an F8E4 code, must be emptied, and the supply shut off if the code appears. [1][2][3]

A Maytag freezer's temperature alarm buzzes when the inside is 10°F (-12°C) or more above the normal level for its setting, and a three-position switch tests, enables or silences it. On a chest freezer, green means the compressor is running and red means the temperature is not low enough, which a big food load, a warm location or a lid left open often explains. [1][2][4][5]

Turn both off, then detach the inlet hoses and empty them first.
Read the full sequence
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.

The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.
For a top-load washer showing LF, Maytag prints “If F8 E1 or LF (long fill) appears in the display, the washer is taking too long to fill.” No reset is printed for it, so schedule a visit if it keeps appearing.
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
After every load. A full screen and a long vent slow drying and raise heat, which is why the guide starts there.
Prop the door open once laundry is out, so the drum can dry. The guide lists the upkeep steps Product Help gives and what a technician should handle.
A rinse under the tap when food builds up. The steps follow Maytag's own page and stop before anything needs tools.
No, but it removes frequent culprits like lint, suds and clogged filters. Parts still wear with age.
Maytag codes, symptoms, parts and service
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.