Diagnostics and repair
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
The care journal
Something quit on you? Begin with the checks your manual permits, and learn when it is time to call a technician.

A Maytag top-load washer that stops agitating or spinning is most often reacting to the load or the setup, not to a broken part. Check balance, the cycle choice, the drain hose and standpipe, the level of the cabinet, a recent power cut, and anything resting on or under the lid. If dU or LdL stays on after that, book a technician. [1][2][3][4]

When a Maytag electric dryer tumbles with no heat, check the household supply before the machine: both breakers of its 30-amp, 240-volt circuit, the power cord and the terminal screws. An L2 or F4 E4 code points the same way, and a five-minute breaker reset is the step Maytag gives. F4 E1 names the heater or its relays and uses a one-minute reset. [1][2][3][4]

After a power cut, a Maytag electric range may show F9 or F9 E0 because of noise on the line. Cut the range's breaker for 60 seconds, restore it, and watch for 60 more. If F9 stays, the outlet may be miswired and an electrician should check the supply. If nothing shows at all, check the breaker or fuse, then the lock, demo and delay settings. [1][2][3]

Water near a Maytag French-door refrigerator usually comes from one of four places: the dispenser (a short pour or full drip tray), the filter (loose seating or overdue), the ice chute (melting shavings) or the supply connection behind the cabinet. Check each in that order, and leave a leaking filter out to run the system in bypass until you have a new one. [1][2][3][4]

Open the door and check three places: the fold of the rubber seal, the detergent drawer cavity and the bottom of the drum. Each one has its own cause on Maytag's pages.
Read the full sequence
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

The door seal, or bellows, on a Maytag front-load washer can trap small items, dirt and pet hair, and then hold water. Product Help says to inspect and clean it monthly and to run the Clean Washer cycle monthly. Its small drain holes can clog and slow draining.

F8E2 on a Maytag front-load washer is a dispenser system problem, and Product Help wants you to confirm the drawer or cartridge is not clogged with detergent. On top-load models F8E2 is the bulk dispenser and F3E5 the mini dispenser. dET means the cartridge is not detected.

Many Maytag front-load washers hide a drain pump filter behind the bottom dispenser drawer. Product Help says to clean it occasionally, because a clogged filter makes the washer drain poorly and can lead to F9E1. Catch the water with a flat container and a cloth first.

F9E1, drn and Ld all mean a Maytag washer is taking too long to drain. Product Help starts with the drain hose: it should not reach too far into the standpipe, must not be taped to the pipe, and must not kink. Front-load pages give 4.5 inches; the top-load page gives 5 inches.
F9E1 reads differently by product type: the front-load washer page states its title reads Long Drain Time; the top-load washer page states its title reads Long Drain. Arrange a technician visit with us if it will not go away.
For a front-load washer showing F8E3, Maytag prints “The overflow condition occurs if there is too much water or foam in the washer.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
Look at power first, then the door or lid, then the water or gas feed. Then open the page for your symptom and ask for a visit if things stay the same.
Cut the power, look for a kink in the drain hose and note any code. If the water stays, ask for a visit instead of forcing the door.
Not advisable. Shut the supply valve, mop up and keep the machine off until someone qualified has inspected it.
Not repeatedly. Leave it unplugged and request a visit. Repeated trips point at the circuit or the heater, and neither is an owner job.
Maytag codes, symptoms, parts and service
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.