Troubleshooting

A range that quit after a power cut or breaker trip

After a power cut, a Maytag electric range may show F9 or F9 E0 because of noise on the line. Cut the range's breaker for 60 seconds, restore it, and watch for 60 more. If F9 stays, the outlet may be miswired and an electrician should check the supply. If nothing shows at all, check the breaker or fuse, then the lock, demo and delay settings. [1][2][3]

A stainless range with a dark display and a flashlight on the counter, an open breaker panel visible in the hallway.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Outage noise can read as a wrong voltage and bring up F9 or F9 E0. 1
  • The reset is a 60-second pause at the breaker plus 60 seconds of watching. 1
  • A returning F9 can mean a miswired outlet; that is an electrician's check. 1
  • A lock, a demo setting or a postponed start can each keep a powered oven cold. 13
  • Elements cycling on and off, or a broil element that drops out with the door open, are normal. 45

Why would a range misbehave after a power cut?#

Maytag's page on a range that stops after an outage says the control can misread the supply. If the power line carried unexpected noise, the control may detect an incorrect voltage and show F9 or F9 E0. The fix it gives is a short breaker reset. 1

The reset has two timed parts: the range's household breaker stays off for a full minute, then power returns and you keep an eye on the display for a further minute to be sure the error stays gone. Then confirm the oven behaves as usual. 1

  1. 1

    Switch the range's breaker off#

    Wait 60 seconds. 1

  2. 2

    Switch it on again#

    Restore power at the household panel. 1

  3. 3

    Observe the range for 60 seconds#

    Check that F9 or F9 E0 does not come back. 1

  4. 4

    Confirm normal operation#

    Start a bake and make sure the oven behaves normally. 1

    A hand rests on a pair of linked breaker switches in an open household breaker panel, a washer and dryer behind.
The reset is a breaker, not a button on the range. 1

What if F9 returns after that?#

Maytag flags this as important: if the display still reads F9 or F9, E0 after the reset, the household outlet could be miswired. Cut power and ask a qualified electrician to verify the supply feeding the range. 1

The same idea appears on our F9 page, which also shows that the wall-oven and steam-oven pages read F9 differently from the range page, so check which kind of appliance you own. The power supply wiring entry describes what the term covers.

A repeat F9 is not something to keep clearing. Each reset only proves the supply is still wrong, and a technician working with an electrician is the sensible next step.

Is the breaker or fuse the answer?#

Sometimes it is plain. Maytag's page on a tripped breaker says to check that a household fuse has not blown or a breaker has not tripped, and to re-set the breaker or put in a new fuse if so. If the problem persists, unplug the cord or switch the breaker off. 2

The same page asks whether the power cord is installed correctly on a newly installed range, with three points to confirm: the strain relief is tightened against the cord, the terminal wires sit in their correct places with matching colors, and the hex nuts on the terminal block posts are secure. 23

Do not open the back of a live range to look at the terminal block. A new installation that never worked is one more reason to book a technician rather than test it yourself.

What if the panel is lit but the oven will not heat?#

Three settings can keep a powered oven cold: the lock, the showroom demo and a postponed start. Each sits on Maytag's list for an electric range that powers on but does not heat. 3

SettingWhat Maytag says
Control LockLook for the words on the control and release it, typically by holding the pad or pads for 3 seconds 13
Demo ModeThe oven does not operate; the control plays a short presentation of the range's features 13
Delayed StartBake waits for the set time; clear the control and begin Bake again from scratch 13

Your model's Owner's Manual explains turning Demo Mode on and off. 3 Our Demo Mode page and Locked page show how Maytag words each message.

A fingertip presses one of six blank square keys beside a dark display on a stainless range control panel.
Control Lock usually releases with a three-second hold. 3

Which oven behaviors are normal?#

Two common worries are not problems. Bake and broil elements cycle on and off during a bake, because a limiter holds temperature at higher settings. And on many models the door must be shut before the elements heat; broil cuts out as soon as it is opened. 45

The elements-cycling page adds that the oven provides accurate temperatures but may cook faster or slower than the range it replaced, so a new Maytag can take a recipe or two to learn. 4 Close the door fully and wait for the broil element to return before assuming anything has failed. 5

What about a gas or dual-fuel range?#

A gas oven has its own short list from Maytag: shut the door completely, confirm the cord sits in a grounded 120-volt outlet that works, and verify that the gas shutoff on the supply line is open. After a new install, a surface burner turned on releases air trapped in the line. 6

Ignitors need a solid ground for their spark, so Maytag says never to use a two-prong adapter or an extension cord, and to prove the outlet with a small working appliance. If the supply is wrong or in doubt, call a qualified electrician. 6

If you ever smell gas, get everyone outside and call the gas company from a safe distance. Do not touch switches or appliances on the way.

Which symptom points to which section?#

What the display does after the outage tells you where to start. Use the table to pick the row that matches, then read the section named beside it. Each row comes from the pages Maytag lists for an electric range that stopped working. 123

What you seeStart here
Display dark, nothing respondsBreaker or fuse, then the power cord on a new install 2
F9 or F9 E0 on the display60-second breaker reset, then an electrician if it returns 1
Display lit, oven stays coldThe lock, demo and delay settings 13
Elements click off and on during a bakeNormal limiter behavior 4
Broil drops out when the door opensNormal; close the door 5

Most of these are quick. A range from this family is built to stand up to years of weeknight cooking, so a stubborn pattern, such as a breaker that trips every time, deserves a proper look instead of one more reset.

Write down the time of the outage, since a storm that cut power twice in a night can explain a control that reset itself.

What helps the technician?#

Describe the outage, whether the display lit afterward, which code appeared and how it responded to the 60-second reset. Say whether the range is new, whether the breaker has tripped before, and which settings you tried.

  • Was there a storm or a flicker before it quit?
  • Dark panel, F9, or lit panel with no heat?
  • Did the one-minute reset clear F9 for good?
  • Is it electric, gas or dual fuel?

The range repair page covers the Maytag ranges we work on, and the oven control entry explains the board behind the display.

Sources#

  1. Not Working After Power Outage - Electric Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-12 · article text: recent power outage, lock and demo mode, delayed start
  2. Circuit Breaker Tripped or Fuse Blown - Electric Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-12 · article text: household breaker or fuse, power cord installed correctly
  3. Oven Not Heating - Powering On - Electric Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: new installation, control lock and demo mode, delayed start
  4. Oven Elements Turning On/Off - Electric Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-12 · article text: elements cycling on and off
  5. Broil Not Working - Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-12 · article text: Is the oven door open?
  6. Oven Not Working - Gas and Dual Fuel Range - Product Help | MaytagMaytag Product Help (producthelp.maytag.com) · retrieved 2026-11-11 · article text: door, gas line air, grounded outlet, main gas valve

Here to help

Good questions.
Clear answers.

Talk to our team
A storm cut the power and my range now shows F9. What happened?

Maytag says electrical noise on the supply during an outage can look like a wrong voltage to the control, which may bring up F9 or F9 E0. Cut the range's breaker for 60 seconds, restore it, and observe for another 60 seconds. [1]

What if F9 keeps coming back after that reset?

Maytag says the household outlet could be miswired. Cut power and ask a qualified electrician to verify the supply feeding the range. [1]

Where do I look when the range is dead and the breaker seems fine?

Check the household fuse or breaker, then the lock, the showroom demo setting and a postponed bake start. Maytag lists each as a reason an electric oven stays cold while its control has power. [2][3]

Should I worry when the oven elements keep clicking on and off?

No. Maytag says bake and broil elements cycle on and off during a bake as a normal feature, because a limiter protects them at higher settings. [4]

The broil element dropped out mid-cook. Why?

Likely the door. Many ovens hold their elements off while the door is ajar, and opening it mid-broil drops the broil element immediately; shutting the door brings it back. [5]

Let’s take care of it.

A full hamper waits for no one.
Book the repair.