Start from the symptom
Maytag range and oven noises.
Most oven noises on a Maytag range are ordinary working sounds. Clicking is the ignitor trying to light the flame, and a fan that runs during and after cooking is the convection or cooling fan. Open the door to tell them apart: the convection fan stops, the cooling fan keeps going.

Start with safe observations.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Clicking
Short taps like a nail on glass come from the ignitors until the flame is detected. Hearing them every 1 to 3 minutes during a cycle is normal.
- 2
Which fan is it?
If the noise stops when you open the door, it is the convection fan. If it carries on, you are hearing the cooling fan.
- 3
Convection fan timing
It is on during preheat in either mode and cuts out when the door is opened. On electric convection models it starts at once on preheat or a convection cycle.
- 4
Cooling fan
The cooling fan starts with cooking and can keep going once the cycle ends, sometimes a long stretch, depending on indoor and oven temperature.
- 5
What the cooling fan protects
It cools the oven cavity and the electronic controls during Bake, Broil or Clean.
Systems a technician may investigate.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

Oven temperature sensor (F1-1, F1-2, F2)
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.

Oven door latch and latch switches (F5)
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects. Product Help gives a one-minute breaker reset and asks you to verify oven operation afterward. A steam oven F5 page lists the reset alone.

Oven control and user interface (F1-7, F1-8, F3, F6)
Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it. F1-8 also names the keypad and its interface. The only home step printed is a one-minute breaker reset, followed by watching the oven.
Read the related care guide.

The range quit after the storm or the breaker: what to check, in order.
After a power cut, a Maytag electric range may show F9 or F9 E0 because of noise on the line. Cut the range's breaker for 60 seconds, restore it, and watch for 60 more. If F9 stays, the outlet may be miswired and an electrician should check the supply. If nothing shows at all, check the breaker or fuse, then the lock, demo and delay settings. [1][2][3]

AquaLift: what the water cycle loosens and what you still wipe by hand.
AquaLift loosens soil with low heat and water; it does not remove everything. On an AquaLift Maytag range, start with a cool, empty, level oven, pour in 2 cups of filtered or distilled water, press AQUALIFT SELF CLEAN then START, allow about 40 minutes, then wipe out the softened soil with a non-scratch sponge. Run it again for stubborn spots, and never use oven cleaners. [1][2][3]
When observation becomes a service request.
Leave internal testing to a technician.
The oven shows Cooling Fan Speed or an F8 code.
Clicking keeps going and the burner or oven will not light.
The fan noise is new, loud or has changed.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Maytag range and oven noises advice. Read the manual for your own model.
- Click or Clicking Noise in Oven - Range - Product Help | Maytag
- Fan Noise - Convection - Range - Product Help | Maytag
- Fan Noise - Non Convection - Range - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Why does my Maytag oven click?
The ignitors click several times until the flame is detected. Product Help describes short taps like a nail on glass, and says one every 1 to 3 minutes during a cycle is normal.
Why is the fan still running after I turn the oven off?
The cooling fan comes on automatically while you cook and after the cycle ends. It cools the cavity and the electronic controls, and can run a long time.
How can I tell a convection fan from the cooling fan?
Open the oven door. If the sound stops, it was the convection fan. If it keeps going, it is the cooling fan, which is meant to run for extended periods.
Which oven noises call for a technician?
When it is new, loud or comes with Cooling Fan Speed, an F8 code, or an oven that will not light. Product Help lists only the clicking and fan sounds above as normal.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Cooling Fan Speed
Maytag lists the airflow restriction, the oven cooling fan or the wiring for Cooling Fan Speed on the range. Reset the power first and watch the display; a returning the code is the cue to book us.
Maytag range and oven noises
Most oven noises on a Maytag range are ordinary working sounds. Clicking is the ignitor trying to light the flame, and a fan that runs during and after cooking is the convection or cooling fan. Open the door to tell them apart: the convection fan stops, the cooling fan keeps going.
Range repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.