Before work starts
Your technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Independent appliance repair
We repair Maytag freestanding and slide-in ranges, electric, gas and dual fuel: an oven that stays cold, burners that tick, a code on the screen, or a door that refuses to latch. Book a technician and we check gas and power first.


Most oven noises on a Maytag range are ordinary working sounds. Clicking is the ignitor trying to light the flame, and a fan that runs during and after cooking is the convection or cooling fan. Open the door to tell them apart: the convection fan stops, the cooling fan keeps going.

A Maytag range self-clean that will not begin is usually waiting on the oven or the door. Too hot and it will not start: AquaLift needs the cavity under 200 degrees F, steam clean under 170 degrees F. On a high-temperature clean the door must close completely or it will not lock. Check which cycle your range has.
Maytag's page on F1-1 for the range says the suspects it lists are control, oven temperature sensor or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
Maytag's page on F1-2 for the range says the suspects it lists are oven temperature sensor, control or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
F1-7 on a Maytag range: Maytag's page says the page names these possible trouble spots: oven control together with its wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. Should the code return once power is back on, arrange a visit with us.
For a Maytag range, Maytag's page for F1-8 says the possible trouble spots it lists are oven control, user interface, keypad or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. Arrange a technician visit with us if the display shows it again after the reset.
Maytag's pages split on F5: the pages for the range and wall oven state the page names these possible trouble spots: door latch switches, oven door latch assembly or wiring; the steam oven page offers a reset and nothing more. To reset it, leave the circuit breaker off for 1 minute before switching it back on.
We pick the part after we read the model label and test the unit. Nothing is ordered ahead of time, and the quote is yours to approve before any work begins.

On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.

F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects. Product Help gives a one-minute breaker reset and asks you to verify oven operation afterward. A steam oven F5 page lists the reset alone.

Maytag range pages for F1-7, F3 and F6 point at the control board of the oven, or the wiring to it. F1-8 also names the keypad and its interface. The only home step printed is a one-minute breaker reset, followed by watching the oven.
Three steps from request to repair.
You stay in the loop the whole way.

Pick washer or dryer and tell us what it does: no spin, no heat, loud thumping. Book online any time.

The technician tests the machine and quotes the work. You approve the price before a tool comes out.

After the repair the technician runs the machine with you and explains what was changed.
Get everyone outside, then phone your gas company or a plumber. Leave switches and flames alone.
After a new install, check strain relief, terminal wires, hex nuts. Also check control lock, demo mode and delayed start.
Close the door fully, check the power cord outlet, and the main gas valve. After a new install, run a surface burner to bleed air from the line.
Ignitors click until the flame is detected. Product Help says every 1 to 3 minutes during the cycle is normal.
For F1-1, F1-2, F1-7, F1-8 and F5, Product Help wants the breaker switched off for 60 seconds, then a watch period.
You smell gas, or a burner will not light.
An F1 or F5 code shows again after a reset.
The oven stays cold although the door is closed and the control unlocked.
The door will not latch.
Arrange a diagnosticYour technician checks the washer, dryer or other appliance, then gives you the cost. The repair goes ahead only with your okay.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
Clicking from the ignitors until flame is detected is normal, roughly every 1 to 3 minutes during the cycle, per Product Help.
Product Help lists: door not closed, power cord not in a grounded outlet, main gas valve off, and trapped air after a new gas connection.
Each names the same three suspects: the sensor in the oven, the control and the wiring. The two pages read alike.
Yes. Ranges have burners or elements on top. Built-in wall ovens have their own service page.
For a unit still covered by the manufacturer's warranty, the maker takes that repair. After coverage ends, schedule a technician with us and approve the quote first.
Maytag codes, symptoms, parts and service
Maytag's page on F1-1 for the range says the suspects it lists are control, oven temperature sensor or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
Most oven noises on a Maytag range are ordinary working sounds. Clicking is the ignitor trying to light the flame, and a fan that runs during and after cooking is the convection or cooling fan. Open the door to tell them apart: the convection fan stops, the cooling fan keeps going.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.