Inside the appliance
Oven temperature sensor (F1-1, F1-2, F2). In plain English.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.

Where it fits.
Oven temperature sensor (F1-1, F1-2, F2) in the appliance
The Product Help pages name the sensor but do not say where it sits on your model. A technician finds it with the oven cool and the power off.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Oven temperature sensor (F1-1, F1-2, F2) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag steam wall oven descale and water container messages
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.

Maytag wall oven locked, in Demo or Sabbath mode, or not responding
A Maytag wall oven that will not heat or will not take commands is often locked, in Demo Mode, in Sabbath Mode, or showing a power-loss clock. Read the display for those first. When Press Cancel to Reset or Call Service appears, cancel and reset the power; should it return, book us for a visit.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Read the code exactly
F1-1 and F1-2 are range pages. F2 is printed for both ranges and wall ovens. Note which string your display shows.
- 2
Reset the breaker
Turn the oven breaker off for one minute, then back on.
- 3
Watch for a minute
Stay near the oven for 60 seconds and see if the display repeats the code.
- 4
Test the oven
Product Help ends with a step to verify oven operation. Try a normal bake setting and see whether it behaves.
Cleaning or replacement?
Leave internal testing to a technician.
The code is back once the oven has run again.
The oven heats unevenly or not at all alongside the code.
You see scorching or melted wiring near the oven back.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Oven temperature sensor (F1-1, F1-2, F2) advice. Read the manual for your own model.
- F1-1 - Error Code -Range - Product Help | Maytag
- F2 - Error Code - Range - Product Help | Maytag
- F2 - Wall Oven - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What does F2 mean on a Maytag oven?
The range and wall oven pages list three suspects, sensor, control and wiring, without ranking them.
Is the sensor a home repair?
The pages print no replacement steps, only the breaker reset. Testing the sensor and the control takes a technician.
Does F1-1 differ from F1-2?
On Maytag ranges both pages print the same sensor, control and wiring wording. We list them together and cannot tell them apart from the text.
Will the reset clear it for good?
It may clear. If the code comes back, we can test the sensor, control and wiring on site.
Maytag codes, symptoms, parts and service
From the message to what you do next.
Maytag oven F1-1 error code
Maytag's page on F1-1 for the range says the suspects it lists are control, oven temperature sensor or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
Maytag steam wall oven descale and water container messages
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Oven repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

