Diagnostics and repair
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
The care journal
What your display code is saying, how similar codes differ and what to try first.

PUSH, Lo, Pre, LOC, 12:00 or POWER LOSS, Demo Mode and Sabbath are messages Maytag's range and wall oven pages describe as instructions or settings, not errors. Press Start for PUSH, wait for Lo to give way to a temperature, hold Start/Enter for LOC, and press Cancel for a power-loss clock. [1][2][3][5]

A flashing Sanitize light, a Control light that blinks three times, and every cycle and option light flashing are not F-E codes on a Maytag dishwasher. They point to water that was too cool, a locked panel, and a door opened mid-cycle. Check those, close the door, and power-cycle for 30 seconds if the pattern stays. [1][2][3]

On a Maytag dryer, group the codes by the first thing each one wants. F4 E3 and the AF or Check Vent light mean airflow: clean the lint screen and vent. F4 E4 and L2 mean the household supply: check both breakers. F1 E1, F3 E3, F4 E1 and F6 E1 mean a breaker reset. PF means the cycle was cut short by a power failure. [1][3][4][5][6][7][8]

After a power outage, a Maytag French-door refrigerator may show PO, which means the freezer reached 18 degrees F (-8 degrees C) or more. Press Measured Fill under Confirm to acknowledge it, then make sure COOLING OFF is dark, the doors are shut, and note whether the Temperature Alarm is flashing. [1][2][4]

Note the code, the cycle and what the machine was doing. A reset clears the display, and the note is what a technician will ask for if the code returns.
Read the full sequence
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.

Where the puddle sits tells you where to look. Water under a Maytag washer most often comes from a loose inlet hose connection, a backed-up household drain, or a cracked hose. Tighten and inspect those first. If the washer is dry at the hoses and still leaks, book a technician.

Water left in the door seal (bellows) of a front-load Maytag washer is usually trapped by dirt, pet hair or a small item under the rubber. Pull the seal back and look all the way around, wipe it clean, and run the Clean Washer cycle each month. A dirty seal can also let water out at the front.

On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.

F4E1 on a Maytag dryer names the heater or the heater relays as the likely problem. Product Help gives a one-minute breaker reset, then a timed dry cycle while you watch the dryer for one minute. For no heat, run a heated timed cycle for five minutes and feel inside.

Long dry times on a Maytag dryer often trace to airflow. F4E3, AF and Check Vent all say the lint screen or vent is clogged, crushed, kinked or has too many turns. Product Help wants the lint screen cleaned after every use and the home venting every one to two years.
F5E1 is a door switch code on both Maytag washer trees. Make sure the door is completely closed and nothing, such as clothing or shipping material, blocks the switch. Then reset for 5 minutes.
F7E1 on a Maytag front-load washer is explained as “This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle...” Try the five-minute power-off reset, and schedule a visit if the code returns.
On a front-load washer, the entry for Err says “Err - Error Message.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
The Maytag page for F1E1 on a Maytag commercial-grade residential dryer or dryer stops at a reset and leaves the cause unstated. To reset it, leave the circuit breaker off for 5 minutes before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
For a commercial-grade residential dryer showing F4E4, Maytag prints “There May be a Problem with the Home Power Supply:.” No reset is printed for it, so schedule a visit if it keeps appearing.
For a commercial-grade residential dryer showing L2, Maytag prints “There May be a Problem with the Home Power Supply:.” Try the one-minute breaker reset, and schedule a visit if the code returns.
On a dryer, the entry for F3E3 says “Power unit down by turning off the circuit breaker(s) for one (1) minute.” Try the one-minute breaker reset, and schedule a visit if the code returns.
Maytag lists the heater or the heater relays for F4E1 on the commercial-grade residential dryer. Reset the power first and watch the display; a returning the code is the cue to book us.
F1E1 on a Maytag dishwasher is explained as “Potential Cause: Control Module.” Cut the power for 30 seconds, then restore it; schedule a visit if the code is still there.
Experienced technicians look the machine over before they suggest any work. OEM parts can be ordered, and the right one is matched to your model.
Maytag deals with repairs its warranty covers. Every repair we complete is backed by our workmanship warranty.
They cover different product types. We print each reading beside its tree, such as top-load or front-load, so nothing is mixed up.
We say that openly, list low-risk checks and recommend a visit. Dryer F1 E1 is one example: the page gives reset steps only.
Some are not. Where a remark concerns control boards, sensors or wiring, we mark it as technician work, and owner advice stays inside what Maytag allows.
Write it down first, then try the reset the page describes. If it returns, the note helps the technician.
Maytag codes, symptoms, parts and service
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.