Maytag microwave E24 / Sensors

Maytag microwave
error code E24

Microwave / display reference

Maytag prints E24 as the oven reaching an overheat condition of 500F (260C). The thermal sensor, gas sensor, appliance control board or wiring may be the cause. Let it cool, reset at the breaker for one minute, and book a visit if it returns.

Also printed as E24

Last reviewed

Microwave / display reference
Meaning
Maytag prints E24 as the oven reaching an overheat condition of 500F (260C). The thermal sensor, gas sensor, appliance control board or wiring may be the cause. Let it cool, reset at the breaker for one minute, and book a visit if it returns.
Who handles it
Reset, then book
Related codes
Source
E24 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave E24 means.

What it means

Maytag prints E24 as the oven reaching an overheat condition of 500F (260C). The thermal sensor, gas sensor, appliance control board or wiring may be the cause. Let it cool, reset at the breaker for one minute, and book a visit if it returns.

What you can safely check

Microwaves keep a charge when unplugged, so the casing stays shut.

When to call a technician

E24 returns after cooling and the one-minute breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag microwave E24: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Let the microwave cool

    The page reports an overheat condition. Cancel the program, open nothing, and wait.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Check the vent

    Make sure nothing blocks the hood vents above and below the microwave. This is our own look; the E24 page does not print it.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Breaker off for one minute

    Then back on, and monitor for one minute.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Do not repeat the same program

    If E24 came up during a long run, tell us what you were cooking.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Keep the housing closed

    Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.

Does E24 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Parts behind the message.

Countertop microwave with its side panel off, showing a small beige sensor module on a green board and a colored wire harness

Component reference

Microwave gas sensor (E11, E12, E24)

On a Maytag over-the-range microwave, E11 and E12 point to the gas sensor or its wiring, and E24 adds a thermal sensor and the control board to that list.

Read the definition

A little more context.

What does E24 say?

The oven reached an overheat condition of 500F (260C). There may be a problem with the thermal sensor, the gas sensor, the appliance control board or the associated wiring.

Read the supporting manual

How is E24 different from E21 and E22?

Those two report the thermal sensor circuit as open or shorted. E24 reports the temperature outcome and widens the list to include the gas sensor.

Read the supporting manual

How does E24 relate to E11?

E11 is a gas sensor report to the control board. E24 includes the gas sensor in its list, so the two share a possible part.

Read the supporting manual

The manual behind the message.

Manufacturer document

E24 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10336 / PH 10336 (over-the-range microwave)

Manufacturer document

E21 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10333 / PH 10333 (over-the-range microwave)

Manufacturer document

E11 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10330 / PH 10330 (over-the-range microwave)

Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10336, with the E21 and E11 pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Did the microwave really reach 500F?

The page says the oven reached an overheat condition of that value, but it cannot tell you whether the sensor or the heat was wrong.

Can I use it after cooling?

Try the reset; if E24 returns, stop.

What blocks a vent?

Cabinetry, trim or stored items. Maytag prints this for the F7E9 code, not for E24.

What do I tell you?

What you cooked and for how long.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.