Inside the appliance
Microwave gas sensor (E11, E12, E24). In plain English.
On a Maytag over-the-range microwave, E11 and E12 point to the gas sensor or its wiring, and E24 adds a thermal sensor and the control board to that list. The one home step in Product Help is a 60-second power-down at the breaker, then a minute of observation.

Where it fits.
Microwave gas sensor (E11, E12, E24) in the appliance
Inside the microwave housing, wired back to the main control board. It is not reachable from the cavity.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Microwave gas sensor (E11, E12, E24) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.

Maytag countertop microwave control panel bubbling
Bubbles on the control panel of a Maytag countertop microwave are usually the clear protective film that ships over the panel. Lift one corner with a fingernail and peel it off; there may be more than one layer. If the panel still looks raised, book a technician.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Note the exact code
E11 says "may be", E12 says "there is" a problem. E24 names more parts.
- 2
Cut power for a minute
Flip the microwave breaker off, count to sixty, then flip it back.
- 3
Watch for one minute
See whether the same code shows again.
- 4
Try a normal cycle
Product Help ends with checking that the microwave works.
Cleaning or replacement?
Leave internal testing to a technician.
E11, E12 or E24 returns after the reset.
The sensor-based cooking choices stop working.
You smell burning or see damaged wiring near the unit.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Microwave gas sensor (E11, E12, E24) advice. Read the manual for your own model.
- E11 - Error Code - Over-the-Range Microwave - Product Help | Maytag
- E12 - Error Code - Over-the-Range Microwave - Product Help | Maytag
- E24 - Error Code - Over-the-Range Microwave - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What does E11 mean?
Product Help ties it to the gas sensor or its wiring, worded as a possibility.
Is E12 worse than E11?
The wording differs: E12 states there is a problem with the gas sensor or wiring, where E11 hedges with a maybe.
Why does E24 list more parts?
Its page names the thermal sensor, gas sensor, control board and wiring, so a technician has to test to narrow it.
What can I try at home?
Power down at the breaker for 60 seconds, restore it, and observe.
Maytag codes, symptoms, parts and service
From the message to what you do next.
E11
Maytag says the gas sensor reported a problem to the control board for E11; the problem may be the gas sensor or its wiring. Reset at the breaker for one minute and monitor for one minute. If E11 returns, book a technician.
Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Microwave repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

