Maytag microwave E11 / Sensors

Maytag microwave
error code E11

Microwave / display reference

Maytag says the gas sensor reported a problem to the control board for E11; the problem may be the gas sensor or its wiring. Reset at the breaker for one minute and monitor for one minute. If E11 returns, book a technician.

Also printed as E11

Last reviewed

Microwave / display reference
Meaning
Maytag says the gas sensor reported a problem to the control board for E11; the problem may be the gas sensor or its wiring. Reset at the breaker for one minute and monitor for one minute. If E11 returns, book a technician.
Who handles it
Reset, then book
Related codes
Source
E11 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave E11 means.

What it means

Maytag says the gas sensor reported a problem to the control board for E11; the problem may be the gas sensor or its wiring. Reset at the breaker for one minute and monitor for one minute. If E11 returns, book a technician.

What you can safely check

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

When to call a technician

E11 returns after the one-minute breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag microwave E11: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Stop any cooking cycle

    Cancel the program and let the cavity cool before you go to the breaker panel.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Breaker off for one minute

    Turn the circuit breaker off for one minute, then back on.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Monitor for one minute

    Watch the display for a full minute before using any cooking function.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Note what you were cooking

    The gas sensor reads vapor from food. Tell us whether E11 came up during a sensor cycle or on a manual time.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Leave the housing closed

    Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.

Does E11 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Parts behind the message.

Countertop microwave with its side panel off, showing a small beige sensor module on a green board and a colored wire harness

Component reference

Microwave gas sensor (E11, E12, E24)

On a Maytag over-the-range microwave, E11 and E12 point to the gas sensor or its wiring, and E24 adds a thermal sensor and the control board to that list.

Read the definition

A little more context.

What does E11 say?

The page reads: the gas sensor reported a problem to the control board, and there may be a problem with the gas sensor or the associated wiring.

Read the supporting manual

How is E11 different from E12?

E12 says “There is a problem with the Gas Sensor or the associated wiring,” without the line about the sensor reporting to the control board. The two pages offer the same reset.

Read the supporting manual

How is E11 different from E24?

E24 is an overheat condition of 500F (260C) and adds the thermal sensor, the control board and the wiring to the list. E11 names only the gas sensor path.

Read the supporting manual

What about E03?

E03 says the keypad reported a problem to the control board. It follows the same pattern as E11, with a different part.

Read the supporting manual

The manual behind the message.

Manufacturer document

E11 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10330 / PH 10330 (over-the-range microwave)

Manufacturer document

E12 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10331 / PH 10331 (over-the-range microwave)

Manufacturer document

E24 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10336 / PH 10336 (over-the-range microwave)

Manufacturer document

E03 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10329 / PH 10329 (over-the-range microwave)

Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10330, with the E12, E24 and E03 pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Is E11 a gas leak?

No. The gas sensor on a microwave reads cooking vapor; it has nothing to do with household gas.

Does E11 stop the microwave?

Maytag does not say. Do not rely on the sensor cycles until the code is gone.

Can I clean the gas sensor?

No cleaning step is printed.

Why does E11 mention the control board?

The page says the sensor reported a problem to the board, so the board saw the signal.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.