What it means
Maytag says for E13: the oven did not pre-heat correctly, and the problem may be the appliance control board or the wiring. Reset at the breaker for one minute and monitor for one minute.
Maytag microwave E13 / Control board
Maytag says for E13: the oven did not pre-heat correctly, and the problem may be the appliance control board or the wiring. Reset at the breaker for one minute and monitor for one minute.
Also printed as E13
Maytag says for E13: the oven did not pre-heat correctly, and the problem may be the appliance control board or the wiring. Reset at the breaker for one minute and monitor for one minute.
Microwaves keep a charge when unplugged, so the casing stays shut.
E13 returns after the one-minute breaker reset.
Your Maytag to-do list, saved here on this device

Stop whatever the microwave was doing when E13 appeared.

Then back on.

Verify microwave operation as the page says.
E13 is about pre-heating. Tell us which mode or program you used.
Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The oven did not pre-heat correctly. There may be a problem with the appliance control board or the associated wiring.
Read the supporting manualE23 says the oven did not reach pre-heat temperature within 30 minutes and names the heater, the control board or the wiring. E13 gives no time limit and names no heater.
Read the supporting manualE12 concerns the gas sensor. E13 concerns pre-heating and the control board.
Read the supporting manualE21 reports the thermal sensor circuit as open. Neither page links to the other.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10332 / PH 10332 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10331 / PH 10331 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10335 / PH 10335 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10333 / PH 10333 (over-the-range microwave)
Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10332, with the E12, E23 and E21 pages.
The page sits in the over-the-range microwave tree and talks about pre-heating, so it fits models with a pre-heat function. Product Help lists no models, so check the code on your own display.
Not necessarily. Maytag names the appliance control board and the wiring as possible causes but does not say which one, and it prints no test for either.
The reset is the only step Maytag prints: breaker off for one minute, back on, then watch the microwave for one minute. If E13 comes back after that, it is time to book a visit.
Maytag prints no safety warning for E13. As a precaution, do not run cooking programs while the code is on, and stop using the microwave if you smell burning.
Maytag codes, symptoms, parts and service
Maytag words E12 as “a problem with the Gas Sensor or the associated wiring.” Turn the breaker off for one minute and monitor for one minute. If E12 returns, schedule a technician.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.