Maytag microwave E21 / Sensors

Maytag microwave
error code E21

Microwave / display reference

Maytag words E21 as the thermal sensor circuit reporting open to the control board. The thermal sensor, the control board or the wiring may be the cause. Reset at the breaker for one minute; book a technician if E21 returns.

Also printed as E21

Last reviewed

Microwave / display reference
Meaning
Maytag words E21 as the thermal sensor circuit reporting open to the control board. The thermal sensor, the control board or the wiring may be the cause. Reset at the breaker for one minute; book a technician if E21 returns.
Who handles it
Reset, then book
Related codes
Source
E21 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave E21 means.

What it means

Maytag words E21 as the thermal sensor circuit reporting open to the control board. The thermal sensor, the control board or the wiring may be the cause. Reset at the breaker for one minute; book a technician if E21 returns.

What you can safely check

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

When to call a technician

E21 returns after the one-minute breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag microwave E21: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Cancel and let it cool

    Cancel the program so the cavity cools while the circuit is open.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Breaker off for one minute

    Then on again.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Monitor for one minute

    Verify operation after power returns.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Compare with E22

    E21 is open; E22 is shorted. Record which one you saw.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Leave the housing closed

    Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.

Does E21 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does E21 say?

The thermal sensor circuit reported open to the control board. The page lists the thermal sensor, the appliance control board or the wiring as possible problems.

Read the supporting manual

What is the difference between E21 and E22?

E22 words the same circuit as reporting a short. An open and a short are opposite electrical conditions, and Maytag prints both with the same reset.

Read the supporting manual

How does E24 relate?

E24 is an overheat condition of 500F (260C), and it names the thermal sensor, the gas sensor, the control board or the wiring.

Read the supporting manual

Is there a cavity thermistor code too?

F3C names the cavity temperature thermistor or wiring. It is separate from the thermal sensor in E21.

Read the supporting manual

The manual behind the message.

Manufacturer document

E21 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10333 / PH 10333 (over-the-range microwave)

Manufacturer document

E22 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10334 / PH 10334 (over-the-range microwave)

Manufacturer document

E24 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10336 / PH 10336 (over-the-range microwave)

Manufacturer document

F3C - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10356 / PH 10356 (over-the-range microwave)

Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10333, with the E22, E24 and F3C pages.

Here to help

Good questions.
Clear answers.

Talk to our team
What does open mean?

The sensor circuit does not complete, so the control sees no temperature signal.

Is E21 a heat problem?

It reports the sensor circuit, not heat itself.

Will the microwave heat?

Maytag does not say.

Is it the control board?

It is one of three possibilities the page lists.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.