Inside the appliance
Microwave humidity sensor (F3H1, F3H, F4E4). In plain English.
On a Maytag over-the-range microwave, F3H1 names the humidity sensor, while F3H and F4E4 name the humidity thermistor, and their wiring. The pages share one step: cut power at the breaker for 60 seconds, restore it, and see whether the code reappears within a minute.

Where it fits.
Microwave humidity sensor (F3H1, F3H, F4E4) in the appliance
Inside the housing of an over-the-range microwave, wired to the control board.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Microwave humidity sensor (F3H1, F3H, F4E4) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.

Maytag countertop microwave control panel bubbling
Bubbles on the control panel of a Maytag countertop microwave are usually the clear protective film that ships over the panel. Lift one corner with a fingernail and peel it off; there may be more than one layer. If the panel still looks raised, book a technician.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Match the code
F3H1 is the sensor. F3H and F4E4 are the thermistor.
- 2
Reset at the breaker
Sixty seconds without power, then restore it.
- 3
Watch for a minute
See whether the same code appears again.
- 4
Run a cycle
Confirm the microwave goes through a normal run.
Cleaning or replacement?
Leave internal testing to a technician.
The same code appears again after the reset.
Steam-sensing cooking choices stop finishing.
The display or fan acts oddly along with the code.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Microwave humidity sensor (F3H1, F3H, F4E4) advice. Read the manual for your own model.
- F3H1 - Error Code - Over-the-Range Microwave - Product Help | Maytag
- F3H - Error Code - Over-the-Range Microwave - Product Help | Maytag
- F4E4 - Error Code - Over-the-Range Microwave - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
What is F3H1?
Product Help ties it to the humidity sensor or its wiring, worded as a possibility.
How do F3H and F4E4 differ from F3H1?
They name the humidity thermistor rather than the sensor. Both pages print the same reset.
Will a reset fix it?
The pages stop at the reset and a minute of watching. A code that comes back needs testing.
Is this on countertop models?
No. These pages are for over-the-range microwaves.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F3H1
Maytag words F3H1 as a possible problem with the humidity sensor or its wiring. Reset at the breaker for one minute and monitor the oven for one minute; schedule a technician if F3H1 returns.
Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Microwave repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

