What it means
Maytag words F3H1 as a possible problem with the humidity sensor or its wiring. Reset at the breaker for one minute and monitor the oven for one minute; schedule a technician if F3H1 returns.
Maytag microwave F3H1 / Sensors
Maytag words F3H1 as a possible problem with the humidity sensor or its wiring. Reset at the breaker for one minute and monitor the oven for one minute; schedule a technician if F3H1 returns.
Also printed as F3H1
Maytag words F3H1 as a possible problem with the humidity sensor or its wiring. Reset at the breaker for one minute and monitor the oven for one minute; schedule a technician if F3H1 returns.
Microwaves keep a charge when unplugged, so the casing stays shut.
F3H1 returns after the one-minute breaker reset.
Your Maytag to-do list, saved here on this device

End cooking and let the cavity clear.

Then on, and monitor the oven for one minute.

As the page says.

F3H1 says sensor; F3H and F4E4 say thermistor.
Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag over-the-range microwave, F3H1 names the humidity sensor, while F3H and F4E4 name the humidity thermistor, and their wiring.
Read the definitionThere may be a problem with the humidity sensor or the associated wiring.
Read the supporting manualF3H says humidity thermistor.
Read the supporting manualF4E4 also says humidity thermistor.
Read the supporting manualYes, one minute at the breaker.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10357 / PH 10357 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10358 / PH 10358 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10364 / PH 10364 (over-the-range microwave)
Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10357, with the F3H and F4E4 pages.
Yes. The page names the humidity sensor and its wiring and nothing else. F3H and F4E4 name the humidity thermistor instead, and Maytag does not explain what that wording changes.
Maytag does not say. The page lists a possible problem with the humidity sensor or the wiring and gives no cause such as steam, so do not assume one.
Maytag does not say whether sensor programs still work. Use plain timed cooking until the code is gone after the reset, and book a visit if F3H1 returns.
Give us the microwave model, the exact code and the program you were using. Also say whether the one-minute breaker reset cleared the code.
Maytag codes, symptoms, parts and service
Maytag words F3C as a possible problem with the cavity temperature thermistor or its wiring. Reset at the breaker for one minute and monitor for one minute. F4E1 names the same part under a different code.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
On a Maytag over-the-range microwave, F3H1 names the humidity sensor, while F3H and F4E4 name the humidity thermistor, and their wiring. The pages share one step: cut power at the breaker for 60 seconds, restore it, and see whether the code reappears within a minute.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.