Maytag microwave E12 / Sensors

Maytag microwave
error code E12

Microwave / display reference

Maytag words E12 as “a problem with the Gas Sensor or the associated wiring.” Turn the breaker off for one minute and monitor for one minute. If E12 returns, schedule a technician.

Also printed as E12

Last reviewed

Microwave / display reference
Meaning
Maytag words E12 as “a problem with the Gas Sensor or the associated wiring.” Turn the breaker off for one minute and monitor for one minute. If E12 returns, schedule a technician.
Who handles it
Reset, then book
Related codes
Source
E12 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave E12 means.

What it means

Maytag words E12 as “a problem with the Gas Sensor or the associated wiring.” Turn the breaker off for one minute and monitor for one minute. If E12 returns, schedule a technician.

What you can safely check

Microwaves keep a charge when unplugged, so the casing stays shut.

When to call a technician

E12 returns after the one-minute breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag microwave E12: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Cancel and cool

    Cancel the program and let the cavity cool.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    One minute at the breaker

    Off for a full minute, then on.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Watch the display

    Monitor for one minute and verify microwave operation, as the page says.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Try a manual time

    If E12 clears, a short manual time shows the microwave heating; sensor cycles are the part to distrust.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Do not open the housing

    Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.

Does E12 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Parts behind the message.

Countertop microwave with its side panel off, showing a small beige sensor module on a green board and a colored wire harness

Component reference

Microwave gas sensor (E11, E12, E24)

On a Maytag over-the-range microwave, E11 and E12 point to the gas sensor or its wiring, and E24 adds a thermal sensor and the control board to that list.

Read the definition

A little more context.

What does the E12 page say?

There is a problem with the gas sensor or the associated wiring. It then gives the one-minute breaker reset and tells you that you may need a qualified technician.

Read the supporting manual

Why have two gas sensor codes?

E11 says the gas sensor reported a problem to the control board. E12 states the problem directly. Maytag does not explain the difference.

Read the supporting manual

How is E12 different from E13?

E13 says the oven did not pre-heat correctly and points to the appliance control board or wiring.

Read the supporting manual

How is E12 different from E21?

E21 reports the thermal sensor circuit as open. E12 involves the gas sensor, not the thermal sensor.

Read the supporting manual

The manual behind the message.

Manufacturer document

E12 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10331 / PH 10331 (over-the-range microwave)

Manufacturer document

E11 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10330 / PH 10330 (over-the-range microwave)

Manufacturer document

E13 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10332 / PH 10332 (over-the-range microwave)

Manufacturer document

E21 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10333 / PH 10333 (over-the-range microwave)

Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10331, with the E11, E13 and E21 pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Is E12 more serious than E11?

The pages give no ranking.

Does E12 involve gas piping?

No. It is the microwave’s vapor sensor.

Do I need a technician?

The page says you may need a qualified technician if the code remains.

What do I tell you?

The exact code, and whether it came with a sensor cooking cycle.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.