What it means
Maytag's over-the-range microwave page links E03 to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag microwave E03 / User interface
Maytag's over-the-range microwave page links E03 to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as E03
Maytag's over-the-range microwave page links E03 to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Microwaves keep a charge when unplugged, so the casing stays shut.
E03 returns, or the over-the-range microwave behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Microwaves keep a charge when unplugged, so the casing stays shut.

Record E03 character by character and note the product type: over-the-range microwave.

Cut power at the breaker for a minute, restore it, then check for E03.

Give the microwave a minute on screen after the reset; a returning E03 means schedule a visit.
Press each key on the over-the-range microwave one at a time and note any that do nothing, beep alone or stick.
Keep the model number close and note when E03 appeared and what the over-the-range microwave was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring.
Read the definitionThe over-the-range microwave list ties E03 to the keypad (user interface) or the wiring. That is a set of candidates, and the page does not pick one.
Read the supporting manualTake the microwave off power at the breaker for a full minute. Put it back on and give it a minute of watching; if E03 stays away, the reset did its job.
Read the supporting manualE11 sits beside E03 on the over-the-range microwave page and names the gas sensor or the wiring; the code names the keypad (user interface) or the wiring.
Read the supporting manualThe over-the-range microwave is fine to use only if you can start and stop it with certainty.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10329 / PH 10329 (over-the-range microwave)
Facts for E03 are from the over-the-range microwave table (PH 10329) of Maytag Product Help, checked November 2026; no model list is printed.
The over-the-range microwave page ties E03 to the keypad (user interface) or the wiring without saying which has failed.
Yes, give it the whole minute. If E03 is still there afterward, schedule a visit.
The list is the keypad (user interface) or the wiring; testing on site settles it.
Tell us the model, the display wording and when E03 first showed up.
Maytag codes, symptoms, parts and service
Maytag says the gas sensor reported a problem to the control board for E11; the problem may be the gas sensor or its wiring. Reset at the breaker for one minute and monitor for one minute. If E11 returns, book a technician.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring. Each page prints the same single step: cut power at the breaker for 60 seconds, restore it, wait a minute for a repeat, then run a cycle.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.