What it means
For E23, the Maytag over-the-range microwave page points to the heater, the appliance control board or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Maytag microwave E23 / Heating
For E23, the Maytag over-the-range microwave page points to the heater, the appliance control board or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Also printed as E23
For E23, the Maytag over-the-range microwave page points to the heater, the appliance control board or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.
E23 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

Match the label on your appliance to the over-the-range microwave list before you rely on the wording for E23.

Leave the breaker off a whole minute before checking for E23 again.
Once power is back, keep an eye on the microwave for about a minute for E23.
Ask yourself whether a power cut, storm or cleaning cycle came just before E23.
Write down the model and serial numbers and the exact E23 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Maytag's over-the-range microwave page says E23 may come from the heater, the appliance control board or the wiring. It stops there; no test and no ranking is given.
Read the supporting manualTake the microwave off power at the breaker for a full minute. Put it back on and give it a minute of watching; if E23 stays away, the reset did its job.
Read the supporting manualRead the exact display: E22 means the thermal sensor, the appliance control board or the wiring on the over-the-range microwave page, and E23 means the heater, the appliance control board or the wiring.
Read the supporting manualIf the over-the-range microwave behaves after the reset, using it is up to you; if E23 returns, stop and schedule a visit. Never open a panel on the over-the-range microwave yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10335 / PH 10335 (over-the-range microwave)
Scope for E23: Maytag over-the-range microwave, PH 10335, checked November 2026. Maytag lists no models on the E23 page.
E23 is printed against the heater, the appliance control board or the wiring; the page does not narrow it down.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If E23 returns, schedule a visit.
Not from the code alone: the entry lists the heater, the appliance control board or the wiring and stops.
The model and serial numbers, the exact display for E23, and what the over-the-range microwave was doing at the time.
Maytag codes, symptoms, parts and service
Maytag words E22 as the thermal sensor circuit reporting a short to the control board. The thermal sensor, the appliance control board or the wiring may be the cause. Reset at the breaker for one minute; book a technician if it returns.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.