What it means
Maytag's top-load washer page words Rinse Light On like this: “Certain cycles use a spray rinse, which adds water to the tub while the basket spins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer Rinse Light On / Water and drain
Maytag's top-load washer page words Rinse Light On like this: “Certain cycles use a spray rinse, which adds water to the tub while the basket spins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as Rinse Light On
Maytag's top-load washer page words Rinse Light On like this: “Certain cycles use a spray rinse, which adds water to the tub while the basket spins.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Power and water off before any panel comes off; towels down for spills.
Rinse Light On returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the top-load washer list before you rely on the wording for Rinse Light On.

No reset is printed here; note the behavior of the washer around Rinse Light On instead.

Note the model and the moment Rinse Light On showed up; both help us plan.

Look for water on the floor around the top-load washer before you restart a cycle.
Write down the model and serial numbers and the exact Rinse Light On wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Here is what Maytag prints for Rinse Light On on a top-load washer: “Certain cycles use a spray rinse, which adds water to the tub while the basket spins.”
Read the supporting manualMaytag's page for Rinse Light On gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualLid Light Flashing is a separate entry from Rinse Light On on the top-load washer page, with its own wording.
Read the supporting manualIf water collects on the floor, shut the taps and switch the top-load washer off. If Rinse Light On keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-04-15; PH 13144 / PH 13144 (top-load washer)
Facts for Rinse Light On are from the top-load washer table (PH 13144) of Maytag Product Help, checked November 2026; no model list is printed.
The help page states “Certain cycles use a spray rinse, which adds water to the tub while the basket spins.” Nothing else is added.
No; Maytag gives Rinse Light On no reset steps. If it repeats, schedule a visit.
Maytag names no part here. Read the message and follow the steps.
Tell us the model, the display wording and when Rinse Light On first showed up.
Maytag codes, symptoms, parts and service
Lid Light Flashing on a Maytag top-load washer is explained as “Your previous washer may have filled and washed with the lid open.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.