What it means
Lid Light Flashing on a Maytag top-load washer is explained as “Your previous washer may have filled and washed with the lid open.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Maytag washer Lid Light Flashing / Door and lid
Lid Light Flashing on a Maytag top-load washer is explained as “Your previous washer may have filled and washed with the lid open.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Also printed as Lid Light Flashing
Lid Light Flashing on a Maytag top-load washer is explained as “Your previous washer may have filled and washed with the lid open.” Maytag prints no reset for it; if it keeps appearing, schedule a visit.
Power and water off before any panel comes off; towels down for spills.
Lid Light Flashing returns, or the top-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the top-load washer list before you rely on the wording for Lid Light Flashing.

No reset is printed here; note the behavior of the washer around Lid Light Flashing instead.

Keep the model number close and note when Lid Light Flashing appeared and what the top-load washer was doing.

Open the door or lid of the top-load washer fully and close it again firmly; check nothing is caught in the seal or latch area.
Keep the model number close and note when Lid Light Flashing appeared and what the top-load washer was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Lid Light Flashing is covered by this wording on the top-load washer page: “Your previous washer may have filled and washed with the lid open.”
Read the supporting manualMaytag's page for Lid Light Flashing gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.
Read the supporting manualFill or Sensing Light On is a separate entry from Lid Light Flashing on the top-load washer page, with its own wording.
Read the supporting manualDo not bypass or tape a door switch on the top-load washer.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-04-15; PH 13143 / PH 13143 (top-load washer)
Facts for Lid Light Flashing are from the top-load washer table (PH 13143) of Maytag Product Help, checked November 2026; no model list is printed.
The help page states “Your previous washer may have filled and washed with the lid open.” Nothing else is added.
No; Maytag gives Lid Light Flashing no reset steps. If it repeats, schedule a visit.
Nothing about replacing parts is printed for Lid Light Flashing.
The model and serial numbers, the exact display for Lid Light Flashing, and what the top-load washer was doing at the time.
Maytag codes, symptoms, parts and service
The Maytag page for Fill or Sensing Light On on a top-load washer states “When the Start/Stop button is pressed and the Water Level knob is set to Auto Sensing, the washer will fill...” No reset is printed for it, so schedule a visit if it keeps appearing.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.