What it means
Maytag words F9 as “The oven could not execute the function,” and lists the appliance control board, the relay control board or the wiring. Reset at the breaker for one minute; if F9 returns, schedule a technician.
Maytag microwave F9 / Information
Maytag words F9 as “The oven could not execute the function,” and lists the appliance control board, the relay control board or the wiring. Reset at the breaker for one minute; if F9 returns, schedule a technician.
Also printed as F9
Maytag words F9 as “The oven could not execute the function,” and lists the appliance control board, the relay control board or the wiring. Reset at the breaker for one minute; if F9 returns, schedule a technician.
Microwaves keep a charge when unplugged, so the casing stays shut.
F9 returns after the one-minute breaker reset.
Your Maytag to-do list, saved here on this device

Cancel what was running.

Turn the circuit breaker off for one minute, then back on, and monitor the oven for one minute as the page says.

F9Q1 blames the touch pad; F9Q prints no cause.

It shows whether basic heating works.
Do not open the microwave housing; thermistors, boards and wiring sit behind high-voltage parts.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The oven could not execute the function; the problem may be the appliance control board, the relay control board or the associated wiring.
Read the supporting manualF6 lists only the relay control board. F9 lists both boards.
Read the supporting manualF9Q1 names the user interface touch pad. F9Q prints no cause at all, only the reset.
Read the supporting manualThe page does not say which is likelier.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10372 / PH 10372 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10370 / PH 10370 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10367 / PH 10367 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10371 / PH 10371 (over-the-range microwave)
Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10372, with the F9Q1, F6 and F9Q pages.
The page cannot say. It lists both the appliance control board and the relay control board, plus the wiring, and only a technician can test which one is responsible.
No. F9Q prints no cause at all, only the reset, while F9 says the oven could not execute the function and lists two boards. Check the last character on your display.
No. Maytag does not tell you to replace anything, and it does not say which board is likelier. The home step is the breaker reset, and a returning code needs a visit.
Note the exact code and what the microwave was doing when it appeared. Also say whether the one-minute breaker reset cleared the code.
Maytag codes, symptoms, parts and service
Maytag’s F9Q page prints no cause, only the reset: breaker off for one minute, on again, monitor the oven for one minute. If F9Q returns, schedule a technician. F9Q1 and F9 do print causes.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.