What it means
Maytag words F8E5 as “The oven could not execute the function,” with a possible problem in the exhaust air temperature sensor or its wiring. Reset at the breaker for one minute; book a technician if F8E5 returns.
Maytag microwave F8E5 / Information
Maytag words F8E5 as “The oven could not execute the function,” with a possible problem in the exhaust air temperature sensor or its wiring. Reset at the breaker for one minute; book a technician if F8E5 returns.
Also printed as F8E5
Maytag words F8E5 as “The oven could not execute the function,” with a possible problem in the exhaust air temperature sensor or its wiring. Reset at the breaker for one minute; book a technician if F8E5 returns.
Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.
F8E5 returns after the one-minute breaker reset.
Your Maytag to-do list, saved here on this device

An exhaust air sensor reads air leaving the microwave. Make sure nothing blocks the vents; F7E9 tells you to check the upper vent door. [2] This is our look, not an F8E5 step.

Turn the circuit breaker off for one minute, then back on, and monitor the oven for one minute as the page says.

Cancel the cooking program.

It shows whether the code stays away.
Do not open the microwave housing; thermistors, boards and wiring sit behind high-voltage parts.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The oven could not execute the function; there may be a problem with the exhaust air temperature sensor or the associated wiring.
Read the supporting manualF9Q1 blames the user interface touch pad. F8E5 is the one that names a temperature sensor.
Read the supporting manualF7E9 is the blocked vent door overheat page. F8E5 does not mention the vent.
Read the supporting manualMaytag does not say. If the microwave overheats or smells hot, stop.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10369 / PH 10369 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-25; PH 14549 / PH 14549 (over-the-range microwave)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10370 / PH 10370 (over-the-range microwave)
Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10369, with the F7E9 and F9Q1 pages.
Maytag does not say where it sits. The page only names the sensor and its wiring as the possible problem, so locating or testing it is a job for a technician.
The F8E5 page does not say so. Only the F7E9 page tells you to check the upper vent door, so look at the vents but do not assume that is the cause.
No. Maytag prints no cleaning step for it. The only home step is the breaker reset: off for one minute, on again, then one minute of watching.
Note the cooking program and whether the vent fan was running when the code appeared. Also give us the exact code and say whether the reset cleared it.
Maytag codes, symptoms, parts and service
For a over-the-range microwave showing F7E9, Maytag prints “Power unit down by turning off the circuit breaker(s) for one (1) minute.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.