What it means
For a over-the-range microwave showing F7E9, Maytag prints “Power unit down by turning off the circuit breaker(s) for one (1) minute.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Maytag microwave F7E9 / Reset only
For a over-the-range microwave showing F7E9, Maytag prints “Power unit down by turning off the circuit breaker(s) for one (1) minute.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Also printed as F7E9
For a over-the-range microwave showing F7E9, Maytag prints “Power unit down by turning off the circuit breaker(s) for one (1) minute.” Switch the breaker off for a minute, then back on; schedule a visit if the code is still there.
Microwaves keep a charge when unplugged, so the casing stays shut.
F7E9 repeats after the reset.
Your Maytag to-do list, saved here on this device

Microwaves keep a charge when unplugged, so the casing stays shut.

Check that your appliance is an over-the-range microwave and copy F7E9 exactly as the display shows it.

Leave the breaker off a whole minute before checking for F7E9 again.
Once power is back, keep an eye on the microwave for about a minute for F7E9.
Write down the exact words or symbols the over-the-range microwave shows before you do anything.
Keep the model number close and note when F7E9 appeared and what the over-the-range microwave was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Here is what Maytag prints for F7E9 on an over-the-range microwave: “Power unit down by turning off the circuit breaker(s) for one (1) minute.”
Read the supporting manualTake the microwave off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F7E9 stays away, the reset did its job.
Read the supporting manualF7 is a neighbor of F7E9, not a synonym. The reset may overlap; the text does not.
Read the supporting manualUse the over-the-range microwave if it behaves normally; stop if there are odd noises, smells or heat.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-25; PH 14549 / PH 14549 (over-the-range microwave)
Scope for F7E9: Maytag over-the-range microwave, PH 14549, checked November 2026. Maytag lists no models on the F7E9 page.
Maytag's wording is “Power unit down by turning off the circuit breaker(s) for one (1) minute.” That is the whole entry.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If F7E9 returns, schedule a visit.
No part is named for F7E9; the page gives only the wording above.
Model and serial numbers plus a note of what happened when F7E9 appeared.
Maytag codes, symptoms, parts and service
Maytag words F7 as “The oven could not execute the function,” with a possible problem in the appliance control board or the wiring. Reset at the breaker for one minute and monitor for one minute. F7E9, a separate page, is about a blocked upper vent door.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.