Maytag microwave F3T1 / Sensors

Maytag microwave
error code F3T1

Microwave / display referenceF3T1

Maytag's over-the-range microwave page links F3T1 to the user interface thermistor or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.

Also printed as F3T1

Last reviewed

Microwave / display referenceF3T1
Meaning
Maytag's over-the-range microwave page links F3T1 to the user interface thermistor or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Who handles it
Reset, then book
Related codes
Source
F3T1 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave F3T1 means.

What it means

Maytag's over-the-range microwave page links F3T1 to the user interface thermistor or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.

What you can safely check

Microwaves keep a charge when unplugged, so the casing stays shut.

When to call a technician

F3T1 returns, or the over-the-range microwave behaves oddly around the code.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag microwave F3T1: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Stay safe

    Microwaves keep a charge when unplugged, so the casing stays shut.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Record the code

    Match the label on your appliance to the over-the-range microwave list before you rely on the wording for F3T1.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Run the reset

    Leave the breaker off a whole minute before checking for F3T1 again.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Watch afterward

    Give the microwave a minute on screen after the reset; a returning F3T1 means schedule a visit.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    Press each key on the over-the-range microwave one at a time and note any that do nothing, beep alone or stick.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Write it down

    Write down the model and serial numbers and the exact F3T1 wording before you call.

Does F3T1 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does F3T1 stand for on an over-the-range microwave?

For F3T1 the over-the-range microwave entry names the user interface thermistor or the wiring. Nothing in it says which of them has failed.

Read the supporting manual

What is worth doing before I schedule a visit for F3T1?

Take the microwave off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F3T1 stays away, the reset did its job.

Read the supporting manual

Why do F3T1 and F3H sit side by side in Maytag's list?

Maytag lists the humidity thermistor or the wiring against F3H, while F3T1 gets the user interface thermistor or the wiring. They are neighbors in the over-the-range microwave list but separate entries.

Read the supporting manual

Should the family keep using the over-the-range microwave with F3T1 showing?

The over-the-range microwave is fine to use only if you can start and stop it with certainty. If F3T1 keeps returning, stop and schedule a visit.

Read the supporting manual

The manual behind the message.

Manufacturer document

F3T1 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10359 / PH 10359 (over-the-range microwave)

F3T1 comes from Maytag Product Help (PH 10359) for the over-the-range microwave, read in November 2026; the F3T1 entry names no models.

Here to help

Good questions.
Clear answers.

Talk to our team
How should I read F3T1 on my over-the-range microwave?

The over-the-range microwave page ties F3T1 to the user interface thermistor or the wiring without saying which has failed.

Is switching off the breaker enough for F3T1?

It is the page's first step and costs nothing. A returning F3T1 afterward means schedule us.

Does F3T1 point to a single part?

No. the user interface thermistor or the wiring are all candidates and the page gives no way to choose.

What helps most on the first visit for F3T1?

Model and serial numbers plus a note of what happened when F3T1 appeared.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.