What it means
For F2E1, the Maytag over-the-range microwave page points to the user interface / keypad or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Maytag microwave F2E1 / User interface
For F2E1, the Maytag over-the-range microwave page points to the user interface / keypad or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Also printed as F2E1
For F2E1, the Maytag over-the-range microwave page points to the user interface / keypad or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Microwaves keep a charge when unplugged, so the casing stays shut.
F2E1 returns, or the over-the-range microwave behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Microwaves keep a charge when unplugged, so the casing stays shut.

Record F2E1 character by character and note the product type: over-the-range microwave.

Cut power at the breaker for a minute, restore it, then check for F2E1.

Give the microwave a minute on screen after the reset; a returning F2E1 means schedule a visit.
Press each key on the over-the-range microwave one at a time and note any that do nothing, beep alone or stick.
Keep the model number close and note when F2E1 appeared and what the over-the-range microwave was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring.
Read the definitionA over-the-range microwave showing F2E1 is, per Maytag, dealing with a possible problem in the user interface / keypad or the wiring. The page adds no diagnosis.
Read the supporting manualTurn the microwave's circuit breaker off for one minute, switch it back on, then keep an eye on the microwave for a further minute to see whether F2E1 comes back.
Read the supporting manualThe over-the-range microwave list prints F1E4 next to F2E1, but with a different line. Look up the one on your display.
Read the supporting manualIf the display jumps or keys misfire, leave the over-the-range microwave off until a technician has looked. Never open a panel on the over-the-range microwave yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10351 / PH 10351 (over-the-range microwave)
Facts for F2E1 are from the over-the-range microwave table (PH 10351) of Maytag Product Help, checked November 2026; no model list is printed.
F2E1 is printed against the user interface / keypad or the wiring; the page does not narrow it down.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If F2E1 returns, schedule a visit.
Not from the code alone: the entry lists the user interface / keypad or the wiring and stops.
The model and serial numbers, the exact display for F2E1, and what the over-the-range microwave was doing at the time.
Maytag codes, symptoms, parts and service
Maytag words F1E4 as “The oven could not execute the function,” with a possible problem in the appliance control board or the wiring. Reset at the breaker for one minute; book a technician if it returns.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring. Each page prints the same single step: cut power at the breaker for 60 seconds, restore it, wait a minute for a repeat, then run a cycle.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.