What it means
Maytag's over-the-range microwave page links F2H1 to the vent fan and light switch (located on the lower left front side panel) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag microwave F2H1 / Fan and airflow
Maytag's over-the-range microwave page links F2H1 to the vent fan and light switch (located on the lower left front side panel) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as F2H1
Maytag's over-the-range microwave page links F2H1 to the vent fan and light switch (located on the lower left front side panel) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.
F2H1 repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

Record F2H1 character by character and note the product type: over-the-range microwave.

Breaker off for one full minute, then back on, and look for F2H1.
Run the microwave briefly after the reset and see whether F2H1 comes back.
Write down the exact words or symbols the over-the-range microwave shows before you do anything.
Write down the model and serial numbers and the exact F2H1 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag over-the-range microwave, F2H1 and F2H2 name the vent fan and light switch, found on the lower left front side panel, or its wiring.
Read the definitionA over-the-range microwave showing F2H1 is, per Maytag, dealing with a possible problem in the vent fan and light switch (located on the lower left front side panel) or the wiring. The page adds no diagnosis.
Read the supporting manualTurn the microwave's circuit breaker off for one minute, switch it back on, then keep an eye on the microwave for a further minute to see whether F2H1 comes back.
Read the supporting manualMaytag lists the user interface / keypad or the wiring against F2E1, while F2H1 gets the vent fan and light switch (located on the lower left front side panel) or the wiring. They are neighbors in the over-the-range microwave list but separate entries.
Read the supporting manualWhether the over-the-range microwave is safe depends on how it behaves, not the message alone. Never open a panel on the over-the-range microwave yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10352 / PH 10352 (over-the-range microwave)
Facts for F2H1 are from the over-the-range microwave table (PH 10352) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag lists the vent fan and light switch (located on the lower left front side panel) or the wiring. It is a possible-cause list, not a confirmed failure.
Yes, give it the whole minute. If F2H1 is still there afterward, schedule a visit.
Not from the code alone: the entry lists the vent fan and light switch (located on the lower left front side panel) or the wiring and stops.
The model and serial numbers, the exact display for F2H1, and what the over-the-range microwave was doing at the time.
Maytag codes, symptoms, parts and service
For F2E1, the Maytag over-the-range microwave page points to the user interface / keypad or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
On a Maytag over-the-range microwave, F2H1 and F2H2 name the vent fan and light switch, found on the lower left front side panel, or its wiring. The printed step is a 60-second power-down at the breaker, then restoring power and observing the unit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.