Inside the appliance
Microwave vent fan and light switch (F2H1, F2H2). In plain English.
On a Maytag over-the-range microwave, F2H1 and F2H2 name the vent fan and light switch, found on the lower left front side panel, or its wiring. The printed step is a 60-second power-down at the breaker, then restoring power and observing the unit.

Where it fits.
Microwave vent fan and light switch (F2H1, F2H2) in the appliance
Lower left front side panel of an over-the-range microwave, wired to the control board.
This image is an example of the component type. It will not tell you which replacement is right for your model.
How you can tell this system is asking for attention.
Microwave vent fan and light switch (F2H1, F2H2) trouble can show up along with weaker performance or a code that keeps coming back. It takes testing to say whether this component is the reason.

Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.

Maytag countertop microwave control panel bubbling
Bubbles on the control panel of a Maytag countertop microwave are usually the clear protective film that ships over the panel. Lift one corner with a fingernail and peel it off; there may be more than one layer. If the panel still looks raised, book a technician.
Owner care, within the model instructions.
Power the machine down and pull the plug ahead of any check you make yourself. Beware of pooled water and sharp bits of debris. Never handle a wet plug or electrical parts, take off a service panel or go beyond what your model’s owner guide permits.
- 1
Read the code
F2H1 and F2H2 share the same switch wording.
- 2
Find the switch
Product Help places it on the lower left front side panel.
- 3
Reset at the breaker
Sixty seconds without power, then restore it.
- 4
Watch and test
Stay for a minute, then try the fan and light.
Cleaning or replacement?
Leave internal testing to a technician.
The same code appears again after the reset.
The fan or the light stops responding.
The fan runs with no input.
Arrange a diagnosticSources and model boundaries.
These sources stand behind the Microwave vent fan and light switch (F2H1, F2H2) advice. Read the manual for your own model.
- F2H1 - Error Code - Over-the-Range Microwave - Product Help | Maytag
- F2H2 - Error Code - Over-the-Range Microwave - Product Help | Maytag
Follow the guide for your own model, and see how we research these pages.
Where is the switch?
Product Help says it is on the lower left front side panel.
Do F2H1 and F2H2 differ?
Their pages print the same wording and the same reset.
Will the microwave still cook?
Product Help does not say. Run a normal cycle once power is back and judge for yourself.
Is this a countertop code?
No. It belongs to over-the-range models that vent over the range.
Maytag codes, symptoms, parts and service
From the message to what you do next.
F2H1
Maytag's over-the-range microwave page links F2H1 to the vent fan and light switch (located on the lower left front side panel) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag microwave will not start
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Microwave repair
Book a diagnostic for your model, done at the machine.
Find your metro
Office details, and the entry information to pass along.

