Maytag microwave E63 / Sensors

Maytag microwave
error code E63

Microwave / display reference

Maytag words E63 as the oven sensor circuit reporting a shorted condition to the control board, exactly as for E62. Reset at the breaker for one minute and monitor for one minute; if E63 returns, book a technician.

Also printed as E63

Last reviewed

Microwave / display reference
Meaning
Maytag words E63 as the oven sensor circuit reporting a shorted condition to the control board, exactly as for E62. Reset at the breaker for one minute and monitor for one minute; if E63 returns, book a technician.
Who handles it
Reset, then book
Related codes
Source
E63 - Error Code - Over-the-Range Microwave - Product Help | Maytag

What Maytag microwave E63 means.

What it means

Maytag words E63 as the oven sensor circuit reporting a shorted condition to the control board, exactly as for E62. Reset at the breaker for one minute and monitor for one minute; if E63 returns, book a technician.

What you can safely check

Microwaves keep a charge when unplugged, so the casing stays shut.

When to call a technician

E63 returns after the one-minute breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 5 checks done
  1. Maytag microwave E63: A hand wiping the cavity ceiling of an open microwave with a gray microfiber cloth, a small grid of sensor vent holes on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Stop the program

    Cancel cooking.

  2. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 2

    Breaker off for one minute

    Then back on.

  3. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 3

    Monitor for one minute

    Verify operation.

  4. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 4

    Say whether you also saw E62

    The two pages match; seeing both would be a detail worth reporting.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Leave the housing closed

    Do not open the microwave housing; sensors, boards and wiring sit behind high-voltage parts.

Does E63 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does E63 say?

The oven sensor circuit reported a shorted condition to the control board; the sensor, the appliance control board or the associated wiring may be the cause.

Read the supporting manual

What should I expect after the reset?

If the code is gone for a minute and stays gone, resume normal use and watch it.

Read the supporting manual

The manual behind the message.

Manufacturer document

E63 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10339 / PH 10339 (over-the-range microwave)

Manufacturer document

E62 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10338 / PH 10338 (over-the-range microwave)

Manufacturer document

E61 - Error Code - Over-the-Range Microwave - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2021-04-29; PH 10337 / PH 10337 (over-the-range microwave)

Product Help lists no models for this entry; the page covers the over-the-range microwave tree. Source: Product Help PH 10339, with the E62 and E61 pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are E62 and E63 two problems?

Maytag gives no sign they are.

Does E63 mean the control board is dead?

It is one of three possibilities.

Is the reset enough?

Only if the code stays away.

What do you need from me?

The model number and the exact code.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.