Maytag washer Sd / Water and drain

Maytag washer
error code Sd

Washer / display referenceSd

On a top-load washer, the entry for Sd says “If Sd or Sud (excess suds) appears in the display, you have excessive suds in the washer.” No reset is printed for it, so schedule a visit if it keeps appearing.

Also printed as Sd

Last reviewed

Washer / display referenceSd
Meaning
On a top-load washer, the entry for Sd says “If Sd or Sud (excess suds) appears in the display, you have excessive suds in the washer.” No reset is printed for it, so schedule a visit if it keeps appearing.
Who handles it
Information only
Related codes
Source
Sd or 5d - Error Code - Product Help | Maytag

What Maytag washer Sd means.

What it means

On a top-load washer, the entry for Sd says “If Sd or Sud (excess suds) appears in the display, you have excessive suds in the washer.” No reset is printed for it, so schedule a visit if it keeps appearing.

What you can safely check

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

When to call a technician

Sd will not clear after one proper reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer Sd: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Safety first

    Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Record the code

    Check that your appliance is a top-load washer and copy Sd exactly as the display shows it.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Cut the power

    No reset is printed here; note the behavior of the washer around Sd instead.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Check the display

    Note the model and the moment Sd showed up; both help us plan.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    Open the top-load washer and spread the load evenly; very small or very heavy loads can unbalance a spin.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Gather details

    Write down the model and serial numbers and the exact Sd wording before you call.

Does Sd keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What lies behind Sd on a Maytag top-load washer?

Here is what Maytag prints for Sd on a top-load washer: “If Sd or Sud (excess suds) appears in the display, you have excessive suds in the washer.”

Read the supporting manual

What is worth doing before I schedule a visit for Sd?

Maytag's page for Sd gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.

Read the supporting manual

What separates Sd from Lid?

The top-load washer list prints Lid next to Sd, but with a different line. Look up the one on your display.

Read the supporting manual

Do I switch the top-load washer off when Sd comes up?

An unbalanced load is usually a loading matter; the top-load washer is safe to use once the load is redistributed.

Read the supporting manual

The manual behind the message.

Manufacturer document

Sd or 5d - Error Code - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-06-04; PH 13160 / PH 13160 (top-load washer)

Scope for Sd: Maytag top-load washer, PH 13160, checked November 2026. Maytag lists no models on the Sd page.

Here to help

Good questions.
Clear answers.

Talk to our team
What is Sd on a Maytag top-load washer?

Once Sd appears on a top-load washer, the help page states “If Sd or Sud (excess suds) appears in the display, you have excessive suds in the washer.” Nothing else is added.

Can I clear Sd myself?

There is no reset on that page. Note what happens and book us if Sd persists.

Does Sd mean something has failed?

Nothing about replacing parts is printed for Sd.

What helps most on the first visit for Sd?

The model number, what Sd looked like, and whether the reset changed anything.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.