Maytag washer Lo FL / Water and drain

Maytag washer
error code Lo FL

Washer / display referenceLo FL

Maytag's front-load washer page words Lo FL like this: “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Nothing else is printed, so schedule a visit if it repeats.

Also printed as Lo FL

Last reviewed

Washer / display referenceLo FL
Meaning
Maytag's front-load washer page words Lo FL like this: “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Nothing else is printed, so schedule a visit if it repeats.
Who handles it
Owner checks first, then a technician
Source
Lo FL - Front Load Washer - Product Help | Maytag

What Maytag washer Lo FL means.

What it means

Maytag's front-load washer page words Lo FL like this: “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” Nothing else is printed, so schedule a visit if it repeats.

What you can safely check

Power and water off before any panel comes off; towels down for spills.

When to call a technician

Lo FL returns, or the front-load washer behaves oddly around the code.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 6 checks done
  1. Maytag washer Lo FL: Back of a washer with two braided inlet hoses laid on top, their screens visible, plus a drain hose in a standpipe and two shut-off valves on the wall
    Illustration. Follow your model’s instructions.
    Before you begin

    Stay safe

    Power and water off before any panel comes off; towels down for spills.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Record the code

    Match the label on your appliance to the front-load washer list before you rely on the wording for Lo FL.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Cut the power

    No reset is printed here; note the behavior of the washer around Lo FL instead.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Retest briefly

    Write down the model and serial numbers and the exact Lo FL wording before you call.

  5. A technician testing a dryer heating circuit
    Illustration. Follow your model’s instructions.
    Check 5

    Appliance-specific check

    Check both water taps behind the front-load washer are fully open and the hoses are not kinked.

  6. Illustration. Follow your model’s instructions.
    Check 6

    Note the model

    Keep the model number close and note when Lo FL appeared and what the front-load washer was doing.

Does Lo FL keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does Lo FL stand for on a front-load washer?

Maytag's front-load washer page gives Lo FL a single line: “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” It adds nothing about cause.

Read the supporting manual

What goes first when the front-load washer flashes Lo FL?

Maytag's page for Lo FL gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the washer shows.

Read the supporting manual

Can I treat Err like Lo FL?

The front-load washer list prints Err next to Lo FL, but with a different line. Look up the one on your display.

Read the supporting manual

Should the family keep using the front-load washer with Lo FL showing?

If water collects on the floor, shut the taps and switch the front-load washer off.

Read the supporting manual

The manual behind the message.

Manufacturer document

Lo FL - Front Load Washer - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2025-06-04; PH 14585 / PH 14585 (front-load washer)

Lo FL comes from Maytag Product Help (PH 14585) for the front-load washer, read in November 2026; the Lo FL entry names no models.

Here to help

Good questions.
Clear answers.

Talk to our team
What does Maytag say Lo FL means?

With Lo FL on the front-load washer, Maytag's wording is “The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water.” That is the whole entry.

Is there a reset for Lo FL?

The page prints none. Write down what you see and schedule a visit if Lo FL keeps appearing.

Does Maytag tell me what to replace for Lo FL?

Maytag names no part here. Read the message and follow the steps.

What helps most on the first visit for Lo FL?

Tell us the model, the display wording and when Lo FL first showed up.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.