What it means
The Maytag page for Lid Lock Flashing on a top-load washer states “Some models will lock immediately, while others will not lock until after the wash cycle has started.” Nothing else is printed, so schedule a visit if it repeats.
Maytag washer Lid Lock Flashing / Display and signals
The Maytag page for Lid Lock Flashing on a top-load washer states “Some models will lock immediately, while others will not lock until after the wash cycle has started.” Nothing else is printed, so schedule a visit if it repeats.
Also printed as Lid Lock Flashing
The Maytag page for Lid Lock Flashing on a top-load washer states “Some models will lock immediately, while others will not lock until after the wash cycle has started.” Nothing else is printed, so schedule a visit if it repeats.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
Lid Lock Flashing repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the top-load washer list before you rely on the wording for Lid Lock Flashing.

Maytag prints no reset for Lid Lock Flashing, so record what the washer does rather than guessing a fix.

Keep the model number close and note when Lid Lock Flashing appeared and what the top-load washer was doing.

Do not force a locked door or lid; wait for the top-load washer to finish and release.
Write down the model and serial numbers and the exact Lid Lock Flashing wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue.
Read the definitionThe top-load washer entry for Lid Lock Flashing reads “Some models will lock immediately, while others will not lock until after the wash cycle has started.” That is the whole explanation Maytag prints.
Read the supporting manualNo reset is printed for Lid Lock Flashing on the top-load washer page. Writing down what the washer does around the code is the useful thing to do.
Read the supporting manualuL is a separate entry from Lid Lock Flashing on the top-load washer page, with its own wording.
Read the supporting manualIf the door will not open, leave the top-load washer off and book us rather than prying. Never open a panel on the top-load washer yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-05-19; PH 13175 / PH 13175 (top-load washer)
Scope for Lid Lock Flashing: Maytag top-load washer, PH 13175, checked November 2026. Maytag lists no models on the Lid Lock Flashing page.
On the top-load washer page the line is “Some models will lock immediately, while others will not lock until after the wash cycle has started.” No further cause is given.
Nothing is printed for it, so record the display and schedule us if Lid Lock Flashing continues.
Not by itself; the page stops at the line it prints.
Model and serial numbers plus a note of what happened when Lid Lock Flashing appeared.
Maytag codes, symptoms, parts and service
Maytag's top-load washer page words uL like this: “The washer could not remedy the off-balance load via automated methods and now needs manual intervention to...” No reset is printed for it, so schedule a visit if it keeps appearing.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.