What it means
For F3E8, the Maytag wall oven page points to the lower oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Maytag oven F3E8 / Sensors
For F3E8, the Maytag wall oven page points to the lower oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Also printed as F3E8
For F3E8, the Maytag wall oven page points to the lower oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F3E8 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Match the label on your appliance to the wall oven list before you rely on the wording for F3E8.

Cut power at the breaker for a minute, restore it, then check for F3E8.

Run the oven briefly after the reset and see whether F3E8 comes back.

Keep foil, pans and racks clear of the sensor area inside the wall oven.
Keep the model number close and note when F3E8 appeared and what the wall oven was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionA wall oven showing F3E8 is, per Maytag, dealing with a possible problem in the lower oven temperature sensor, the control or the wiring. The page adds no diagnosis.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F3E8 stays away, the reset did its job.
Read the supporting manualF3E7 carries the same parts list as F3E8 on the wall oven page. The reset is the same, only the code differs.
Read the supporting manualDo not rely on the dial alone while this is open; a food thermometer is the safer guide. Never open a panel on the wall oven yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14434 / PH 14434 (wall oven)
Facts for F3E8 are from the wall oven table (PH 14434) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag lists the lower oven temperature sensor, the control or the wiring. It is a possible-cause list, not a confirmed failure.
Yes, give it the whole minute. If F3E8 is still there afterward, schedule a visit.
The list is the lower oven temperature sensor, the control or the wiring; testing on site settles it.
Model and serial numbers plus a note of what happened when F3E8 appeared.
Maytag codes, symptoms, parts and service
F3E7 on your wall oven is tied by Maytag to the lower oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.