What it means
F3E6 on a wall oven means Maytag suspects the lower oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Maytag oven F3E6 / Sensors
F3E6 on a wall oven means Maytag suspects the lower oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Also printed as F3E6
F3E6 on a wall oven means Maytag suspects the lower oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
Turn the breaker off before you touch anything behind a panel.
F3E6 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Check that your appliance is a wall oven and copy F3E6 exactly as the display shows it.

Leave the breaker off a whole minute before checking for F3E6 again.

Give the oven a minute on screen after the reset; a returning F3E6 means schedule a visit.

Watch whether the wall oven reaches and holds the temperature you set; a sensor problem often shows up as food that cooks too fast or too slowly.
Write down the model and serial numbers and the exact F3E6 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionMaytag's wall oven page says F3E6 may come from the lower oven temperature sensor, the control or the wiring. It stops there; no test and no ranking is given.
Read the supporting manualTurn the oven's circuit breaker off for one minute, switch it back on, then keep an eye on the oven for a further minute to see whether F3E6 comes back.
Read the supporting manualF3E5 carries the same parts list as F3E6 on the wall oven page. The reset is the same, only the code differs.
Read the supporting manualUse the wall oven only for simple cooking you can watch, and stop if anything smells burnt.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14432 / PH 14432 (wall oven)
Facts for F3E6 are from the wall oven table (PH 14432) of Maytag Product Help, checked November 2026; no model list is printed.
The wall oven page ties F3E6 to the lower oven temperature sensor, the control or the wiring without saying which has failed.
Try it first: one minute off, one minute on screen. If F3E6 persists, a technician should look.
The list is the lower oven temperature sensor, the control or the wiring; testing on site settles it.
The model and serial numbers, the exact display for F3E6, and what the wall oven was doing at the time.
Maytag codes, symptoms, parts and service
For F3E5, the Maytag wall oven page points to the lower oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.