What it means
F3 E4 is a probe code. On a range Maytag says verify the meat probe is seated in the receptacle. The wall oven page adds a second cause, a power attachment that came unplugged. Both then ask for the one-minute breaker reset.
Maytag oven F3E4 / Sensors
F3 E4 is a probe code. On a range Maytag says verify the meat probe is seated in the receptacle. The wall oven page adds a second cause, a power attachment that came unplugged. Both then ask for the one-minute breaker reset.
Also printed as F3E4
F3 E4 is a probe code. On a range Maytag says verify the meat probe is seated in the receptacle. The wall oven page adds a second cause, a power attachment that came unplugged. Both then ask for the one-minute breaker reset.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F3 E4 returns after the probe check, the rack check and the reset.
Your Maytag to-do list, saved here on this device

If so, verify it is securely inserted in the meat probe receptacle. Location varies; the owner's manual shows it.

On some wall ovens a roll-out rack attachment may have come unplugged. Roll out the rack, check the attachment, and push the rack firmly in until a tone sounds.

Breaker off for one minute, then on, and watch the oven for a minute.

On a combination model, the microwave probe is a different part. See the F4 E7 note below.
Give us the model and the checks you have run, then open your request right here.
Book a visit


A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
The range page has one instruction: verify meat probe is securely inserted in the meat probe receptacle, location may vary.
Read the supporting manualThe wall oven page says the code "can be caused by either a dislocated meat probe or power attachment (depending on model number)." It asks if the probe was being used and if a power attachment was in use.
Read the supporting manualOn a combination wall oven, F4 E7 is the microwave meat probe code. Maytag says do not use the oven meat probe in the microwave because they have different resistance values.
Read the supporting manualThe reset is the last step the pages give. A code that returns after it needs a technician to test the probe jack and wiring.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13778 / PH 13778 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-06-02; PH 14430 / PH 14430 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14445 / PH 14445 (wall oven)
Product Help range page PH 13778 and wall oven page PH 14430 (modified June 2025), plus the wall oven F4 E7 page PH 14445 for the microwave probe note.
Not on either page. They point to a probe or a power attachment, not to a temperature sensor.
Maytag says only that it is available on some models.
No. The F4 E7 page says they have different resistance values.
No. Only the wall oven page does.
Maytag codes, symptoms, parts and service
F3 E3 reads differently on the two trees. The range page names the oven temperature sensor or the wiring, with no control. The wall oven page adds the control. Switch the breaker off for one minute and back on, then book a visit if it returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.