What it means
Maytag's range page links F3E2 to the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag oven F3E2 / Sensors
Maytag's range page links F3E2 to the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as F3E2
Maytag's range page links F3E2 to the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Turn the breaker off before you touch anything behind a panel.
F3E2 returns, or the range behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Record F3E2 character by character and note the product type: range.

Cut power at the breaker for a minute, restore it, then check for F3E2.

Give the oven a minute on screen after the reset; a returning F3E2 means schedule a visit.

Watch whether the range reaches and holds the temperature you set; a sensor problem often shows up as food that cooks too fast or too slowly.
Write down the model and serial numbers and the exact F3E2 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionF3E2 is printed against the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring. Maytag words it as a possible problem, not a finding.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F3E2 stays away, the reset did its job.
Read the supporting manualRead the exact display: F3E1 means the oven temperature sensor, the control or the wiring on the range page, and F3E2 means the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring.
Read the supporting manualUse the range only for simple cooking you can watch, and stop if anything smells burnt.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13776 / PH 13776 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14428 / PH 14428 (wall oven)
Facts for F3E2 are from the range table (PH 13776) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag lists the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring. It is a possible-cause list, not a confirmed failure.
Try it first: one minute off, one minute on screen. If F3E2 persists, a technician should look.
Not from the code alone: the entry lists the oven temperature sensor, the warming drawer sensor (if so equipped) or the wiring and stops.
The model and serial numbers, the exact display for F3E2, and what the range was doing at the time.
Maytag codes, symptoms, parts and service
F3 E1 names the oven temperature sensor, the control or the wiring. On a wall oven Maytag says "Lower Oven Temperature Sensor", which tells a double oven which cavity to report. Switch the breaker off for one minute and back on; book a visit if it returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.