What it means
F3E7 on your wall oven is tied by Maytag to the lower oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Maytag oven F3E7 / Sensors
F3E7 on your wall oven is tied by Maytag to the lower oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Also printed as F3E7
F3E7 on your wall oven is tied by Maytag to the lower oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Turn the breaker off before you touch anything behind a panel.
F3E7 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Record F3E7 character by character and note the product type: wall oven.

Leave the breaker off a whole minute before checking for F3E7 again.

Once power is back, keep an eye on the oven for about a minute for F3E7.

Watch whether the wall oven reaches and holds the temperature you set; a sensor problem often shows up as food that cooks too fast or too slowly.
Keep the model number close and note when F3E7 appeared and what the wall oven was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionThe wall oven list ties F3E7 to the lower oven temperature sensor, the control or the wiring. That is a set of candidates, and the page does not pick one.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F3E7 stays away, the reset did its job.
Read the supporting manualMaytag gives F3E6 and F3E7 the same wording on the wall oven page, so the same first step fits both.
Read the supporting manualUse the wall oven only for simple cooking you can watch, and stop if anything smells burnt.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14433 / PH 14433 (wall oven)
Facts for F3E7 are from the wall oven table (PH 14433) of Maytag Product Help, checked November 2026; no model list is printed.
F3E7 is printed against the lower oven temperature sensor, the control or the wiring; the page does not narrow it down.
Yes, give it the whole minute. If F3E7 is still there afterward, schedule a visit.
The list is the lower oven temperature sensor, the control or the wiring; testing on site settles it.
The model number, what F3E7 looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
F3E6 on a wall oven means Maytag suspects the lower oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.