What it means
F1 on your range is tied by Maytag to the oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Maytag oven F1 / Sensors
F1 on your range is tied by Maytag to the oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Also printed as F1
F1 on your range is tied by Maytag to the oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F1 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Check that your appliance is a range and copy F1 exactly as the display shows it.

Leave the breaker off a whole minute before checking for F1 again.

Run the oven briefly after the reset and see whether F1 comes back.

Watch whether the range reaches and holds the temperature you set; a sensor problem often shows up as food that cooks too fast or too slowly.
Keep the model number close and note when F1 appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionA range showing F1 is, per Maytag, dealing with a possible problem in the oven temperature sensor, the control or the wiring. The page adds no diagnosis.
Read the supporting manualTurn the oven's circuit breaker off for one minute, switch it back on, then keep an eye on the oven for a further minute to see whether F1 comes back.
Read the supporting manualF1-L carries the same parts list as the code on the range page. The reset is the same, only the code differs.
Read the supporting manualUse the range only for simple cooking you can watch, and stop if anything smells burnt.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13757 / PH 13757 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14405 / PH 14405 (wall oven)
Facts for F1 are from the range table (PH 13757) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag names the oven temperature sensor, the control or the wiring and gives no test to choose between them.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If F1 returns, schedule a visit.
No. the oven temperature sensor, the control or the wiring are all candidates and the page gives no way to choose.
Tell us the model, the display wording and when F1 first showed up.
Maytag codes, symptoms, parts and service
F1-L on your range is tied by Maytag to the oven temperature sensor, the control or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.