What it means
Maytag's range page links F1-3 to the oven temperature sensor, the control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag oven F1-3 / Sensors
Maytag's range page links F1-3 to the oven temperature sensor, the control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as F1-3
Maytag's range page links F1-3 to the oven temperature sensor, the control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
F1-3 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Match the label on your appliance to the range list before you rely on the wording for F1-3.

Leave the breaker off a whole minute before checking for F1-3 again.

Run the oven briefly after the reset and see whether F1-3 comes back.

Keep foil, pans and racks clear of the sensor area inside the range.
Note the model and the moment F1-3 showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionThe range list ties F1-3 to the oven temperature sensor, the control or the wiring. That is a set of candidates, and the page does not pick one.
Read the supporting manualTurn the oven's circuit breaker off for one minute, switch it back on, then keep an eye on the oven for a further minute to see whether F1-3 comes back.
Read the supporting manualMaytag gives F1-H and F1-3 the same wording on the range page, so the same first step fits both.
Read the supporting manualA sensor that misreads can mean wrong temperatures, so check food with a thermometer while the range is in use.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13747 / PH 13747 (range)
F1-3 comes from Maytag Product Help (PH 13747) for the range, read in November 2026; the F1-3 entry names no models.
F1-3 is printed against the oven temperature sensor, the control or the wiring; the page does not narrow it down.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If F1-3 returns, schedule a visit.
No. the oven temperature sensor, the control or the wiring are all candidates and the page gives no way to choose.
The model number, what F1-3 looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
Maytag's page on F1-1 for the range says the suspects it lists are control, oven temperature sensor or wiring. To reset it, leave the circuit breaker off for 1 minute before switching it back on. A repeat of the code after the reset is the cue to schedule a visit with us.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.