What it means
F1-A on your range is tied by Maytag to the oven door latch, the door lock switch or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Maytag oven F1-A / Door and lid
F1-A on your range is tied by Maytag to the oven door latch, the door lock switch or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Also printed as F1-A
F1-A on your range is tied by Maytag to the oven door latch, the door lock switch or the wiring. One reset costs nothing; if the code survives it, schedule a visit.
Turn the breaker off before you touch anything behind a panel.
F1-A will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Check that your appliance is a range and copy F1-A exactly as the display shows it.

Breaker off for one full minute, then back on, and look for F1-A.

Give the oven a minute on screen after the reset; a returning F1-A means schedule a visit.

Look at the door seal on the range: it should close fully with nothing caught in it.
Note the model and the moment F1-A showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects.
Read the definitionA range showing F1-A is, per Maytag, dealing with a possible problem in the oven door latch, the door lock switch or the wiring. The page adds no diagnosis.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if F1-A stays away, the reset did its job.
Read the supporting manualMaytag lists the oven control or the wiring against F1-9, while F1-A gets the oven door latch, the door lock switch or the wiring. They are neighbors in the range list but separate entries.
Read the supporting manualThe page names the latch side, so the lock may not work as it should. Skip self-clean cycles until the range is checked. If F1-A keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13752 / PH 13752 (range)
Scope for F1-A: Maytag range, PH 13752, checked November 2026. Maytag lists no models on the F1-A page.
The range page ties F1-A to the oven door latch, the door lock switch or the wiring without saying which has failed.
Yes, give it the whole minute. If F1-A is still there afterward, schedule a visit.
Maytag names the oven door latch, the door lock switch or the wiring. Which one failed is for a technician with a meter to decide.
Tell us the model, the display wording and when F1-A first showed up.
Maytag codes, symptoms, parts and service
Maytag's range page links F1-9 to the oven control or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
F5 on a Maytag range or wall oven names the door latch assembly, the latch switches and the wiring as suspects. Product Help gives a one-minute breaker reset and asks you to verify oven operation afterward. A steam oven F5 page lists the reset alone.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.