What it means
For 3d22, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Maytag oven 3d22 / Sensors
For 3d22, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Also printed as 3d22
For 3d22, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
3d22 repeats after the reset.
Your Maytag to-do list, saved here on this device

Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.

Record 3d22 character by character and note the product type: range.

Leave the breaker off a whole minute before checking for 3d22 again.

Once power is back, keep an eye on the oven for about a minute for 3d22.

Do not bend or poke the sensor inside the range; panel work belongs to a technician.
Write down the model and serial numbers and the exact 3d22 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionA range showing 3d22 is, per Maytag, dealing with a possible problem in the oven temperature sensor, the control or the wiring. The page adds no diagnosis.
Read the supporting manualTake the oven off power at the breaker for a full minute. Put it back on and give it a minute of watching; if 3d22 stays away, the reset did its job.
Read the supporting manual3d21 and 3d22 name the same suspects in the range list; quote the code you actually see when booking.
Read the supporting manualDo not rely on the dial alone while this is open; a food thermometer is the safer guide.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13710 / PH 13710 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14370 / PH 14370 (wall oven)
Facts for 3d22 are from the range table (PH 13710) of Maytag Product Help, checked November 2026; no model list is printed.
Maytag names the oven temperature sensor, the control or the wiring and gives no test to choose between them.
It sometimes does. Breaker off for a full minute, then on, then a minute of watching. If 3d22 returns, schedule a visit.
The list is the oven temperature sensor, the control or the wiring; testing on site settles it.
Model and serial numbers plus a note of what happened when 3d22 appeared.
Maytag codes, symptoms, parts and service
For 3d21, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.