What it means
For 3d21, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Maytag oven 3d21 / Sensors
For 3d21, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Also printed as 3d21
For 3d21, the Maytag range page points to the oven temperature sensor, the control or the wiring. Treat that as a shortlist, try the reset, and schedule a visit if the code stays.
Turn the breaker off before you touch anything behind a panel.
3d21 repeats after the reset.
Your Maytag to-do list, saved here on this device

Turn the breaker off before you touch anything behind a panel. If you smell gas, leave the house and call your gas utility from outside.

Record 3d21 character by character and note the product type: range.

Cut power at the breaker for a minute, restore it, then check for 3d21.

Run the oven briefly after the reset and see whether 3d21 comes back.

Watch whether the range reaches and holds the temperature you set; a sensor problem often shows up as food that cooks too fast or too slowly.
Keep the model number close and note when 3d21 appeared and what the range was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue.
Read the definitionMaytag's range page says 3d21 may come from the oven temperature sensor, the control or the wiring. It stops there; no test and no ranking is given.
Read the supporting manualTurn the oven's circuit breaker off for one minute, switch it back on, then keep an eye on the oven for a further minute to see whether 3d21 comes back.
Read the supporting manual3d12 carries the same parts list as 3d21 on the range page. The reset is the same, only the code differs.
Read the supporting manualUse the range only for simple cooking you can watch, and stop if anything smells burnt. If 3d21 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13709 / PH 13709 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14369 / PH 14369 (wall oven)
Facts for 3d21 are from the range table (PH 13709) of Maytag Product Help, checked November 2026; no model list is printed.
The range page ties 3d21 to the oven temperature sensor, the control or the wiring without saying which has failed.
Yes, give it the whole minute. If 3d21 is still there afterward, schedule a visit.
Maytag names the oven temperature sensor, the control or the wiring. Which one failed is for a technician with a meter to decide.
Model and serial numbers plus a note of what happened when 3d21 appeared.
Maytag codes, symptoms, parts and service
3d12 on a range means Maytag suspects the oven temperature sensor, the control or the wiring. Begin with the reset; if the code is back afterward, book a technician.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
On a Maytag range or wall oven, F1-1, F1-2 and F2 all carry the same wording in Product Help: the sensor in the oven, the control or the wiring could be at issue. The only home step the pages print is a short breaker reset, and they name no other check.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.