Maytag oven 3d31 / Reset only

Maytag oven
error code 3d31

Oven / display reference3d31

3D31 is a probe-related entry: Maytag says verify the meat probe is securely inserted in the meat probe receptacle, then reset the power. The page names no failed part. A probe that is pushed in fully, and a breaker reset, are the whole at-home fix.

Also printed as 3d31

Last reviewed

Oven / display reference3d31
Meaning
3D31 is a probe-related entry: Maytag says verify the meat probe is securely inserted in the meat probe receptacle, then reset the power. The page names no failed part. A probe that is pushed in fully, and a breaker reset, are the whole at-home fix.
Who handles it
Reset, then book
Related codes
Source
3d31- Error Code - Range - Product Help | Maytag

What Maytag oven 3d31 means.

What it means

3D31 is a probe-related entry: Maytag says verify the meat probe is securely inserted in the meat probe receptacle, then reset the power. The page names no failed part. A probe that is pushed in fully, and a breaker reset, are the whole at-home fix.

What you can safely check

Turn the breaker off before you touch anything behind a panel.

When to call a technician

3D31 stays after the probe is reseated and the breaker reset.

Your Maytag to-do list, saved here on this device

Safe checks, in order.

0 of 4 checks done
  1. Maytag oven 3d31: A fingertip pressing a touch pad on a range control panel with softly glowing white segments, a striped dish towel hanging over the oven door handle.
    Illustration. Follow your model’s instructions.
    Before you begin

    Push the probe in all the way

    Product Help says to verify the meat probe is securely inserted in the receptacle, and that its location may vary by model.

  2. Ranges & ovens in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Check the probe is in the food

    The related Probe message page says the control is looking for an input from the probe and the probe goes in the center of the thickest part of the food.

  3. Close view of a washer control dial and cycle buttons
    Illustration. Follow your model’s instructions.
    Check 3

    Reset the power

    Breaker off for one minute, then on.

  4. Over-the-shoulder view of a technician in a navy shirt holding a tablet with five empty checkboxes, a top-load washer behind
    Illustration. Follow your model’s instructions.
    Check 4

    Watch for one minute

    Monitor the oven for a minute to see whether the code displays again, then check normal oven operation.

Does 3d31 keep coming back?

Give us the model and the checks you have run, then open your request right here.

Book a visit

The touch panel and control.

Conceptual Range / oven sectionKeypad / touch panelControl boardElement wiring123
  1. 1Keypad / touch panel
  2. 3Element wiring

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

A little more context.

What does 3D31 point at?

The range page for 3D31 gives one step before the reset: verify the meat probe is securely inserted in the meat probe receptacle.

Read the supporting manual

What does the Probe message page add?

The separate Probe or Insert Probe page says the control is "looking" for an input from the meat probe.

Read the supporting manual

Where is the receptacle?

Maytag says the location may vary and shows a typical probe and jack picture on the message page. Your owner's manual gives the exact spot.

Read the supporting manual

How is 3D31 different from 3D32 and 3D41?

Maytag prints the same wording for 3D31, 3D32 and 3D41. We found no difference in meaning between them.

Read the supporting manual

The manual behind the message.

Manufacturer document

3d31- Error Code - Range - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-08-16; PH 13711 / PH 13711 (range)

Manufacturer document

3d31 - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14371 / PH 14371 (wall oven)

Manufacturer document

Probe or Insert Probe - Range - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-07; PH 13884 / PH 13884 (range)

Manufacturer document

Probe or Insert Probe - Wall Oven - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-11-08; PH 14349 / PH 14349 (wall oven)

Manufacturer document

3d32 - Error Code - Range - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-08-16; PH 13712 / PH 13712 (range)

Manufacturer document

3d41- Error Code - Range - Product Help | Maytag

Maytag Product Help (producthelp.maytag.com)

dateModified 2024-08-16; PH 13713 / PH 13713 (range)

Product Help range page PH 13711 and wall oven page PH 14371, with the Probe or Insert Probe pages (PH 13884 range, PH 14349 wall oven). No models are listed.

Here to help

Good questions.
Clear answers.

Talk to our team
Do I need the probe for 3D31 to clear?

The page tells you to check it is seated. It does not say the probe has failed.

Can I bake with the probe out?

Maytag does not address it. Try the reset and check that normal bake works.

The probe is in and 3D31 stays. Now what?

Reset the breaker for one minute once. If it returns, book a visit.

Is a part named for 3D31?

No. The page lists the probe step and the reset only.

Let’s take care of it.

A full hamper waits for no one.
Book the repair.