What it means
3D32 uses the same Maytag wording as 3D31 and 3D41: verify the meat probe is securely inserted in its receptacle, then reset the power. If the code survives that, no further cause is printed, so book a visit.
Maytag oven 3d32 / Reset only
3D32 uses the same Maytag wording as 3D31 and 3D41: verify the meat probe is securely inserted in its receptacle, then reset the power. If the code survives that, no further cause is printed, so book a visit.
Also printed as 3d32
3D32 uses the same Maytag wording as 3D31 and 3D41: verify the meat probe is securely inserted in its receptacle, then reset the power. If the code survives that, no further cause is printed, so book a visit.
Power off at the breaker before any panel comes off; a gas smell means getting out and calling the gas utility from outside.
3D32 returns after the probe is seated and the power reset.
Your Maytag to-do list, saved here on this device

Confirm the meat probe is fully inserted in the receptacle. Maytag adds that its location may vary.

The Probe message page says to insert the probe into the center of the thickest part of the food, away from bone.

Off for one minute, on, then monitor the oven for one minute.

Write down whether 3D32 came back, and whether it came back during a probe cycle or a normal bake.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
One instruction before the reset: verify meat probe is securely inserted in the meat probe receptacle.
Read the supporting manualThe pages for 3D31, 3D32 and 3D41 are word for word the same, in both the range and the wall oven trees. Treat them as one probe-input family.
Read the supporting manualThe Probe message page says the control is looking for an input from the meat probe.
Read the supporting manualThen the reset has not cleared whatever the control sensed. Stop using the probe feature and book a visit; we can test the receptacle wiring on site.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-08-16; PH 13712 / PH 13712 (range)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-08; PH 14372 / PH 14372 (wall oven)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2024-11-07; PH 13884 / PH 13884 (range)
Product Help range page PH 13712 and wall oven page PH 14372, plus the Probe message pages PH 13884 and PH 14349. No models are listed.
Maytag does not rank them. The page text is identical.
The Probe message page says to insert the probe into the center of the thickest part of the food.
Into the receptacle in the oven cavity; Maytag says the location may vary.
Maytag does not say that. The listed steps are seating it and resetting the power.
Maytag codes, symptoms, parts and service
3D31 is a probe-related entry: Maytag says verify the meat probe is securely inserted in the meat probe receptacle, then reset the power. The page names no failed part. A probe that is pushed in fully, and a breaker reset, are the whole at-home fix.
A Maytag steam wall oven asks you to "Empty and Refill Water Container" before each steam cycle, "Descale is needed" when it needs cleaning, and "Please remove and empty container" at the end of a descale. Treat each as a request rather than a breakdown, carry it out, and book a visit if one keeps returning.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.