What it means
Maytag's over-the-range microwave page links SE to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Maytag microwave SE / User interface
Maytag's over-the-range microwave page links SE to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Also printed as SE
Maytag's over-the-range microwave page links SE to the keypad (user interface) or the wiring. It does not say which one, so run the reset below and schedule a visit if the code returns.
Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.
SE repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

Record SE character by character and note the product type: over-the-range microwave.

Leave the breaker off a whole minute before checking for SE again.

Run the microwave briefly after the reset and see whether SE comes back.
Wipe the panel of the over-the-range microwave with a dry or barely damp cloth; spills and grease upset keys.
Keep the model number close and note when SE appeared and what the over-the-range microwave was doing.
Give us the model and the checks you have run, then open your request right here.
Book a visit

A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring.
Read the definitionMaytag's over-the-range microwave page says SE may come from the keypad (user interface) or the wiring. It stops there; no test and no ranking is given.
Read the supporting manualTake the microwave off power at the breaker for a full minute. Put it back on and give it a minute of watching; if SE stays away, the reset did its job.
Read the supporting manualDoor or Open Door Closed is a separate entry from SE on the over-the-range microwave page, with its own wording.
Read the supporting manualIf the display jumps or keys misfire, leave the over-the-range microwave off until a technician has looked. Never open a panel on the over-the-range microwave yourself.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2023-08-16; PH 10328 / PH 10328 (over-the-range microwave)
SE comes from Maytag Product Help (PH 10328) for the over-the-range microwave, read in November 2026; the SE entry names no models.
SE is printed against the keypad (user interface) or the wiring; the page does not narrow it down.
Yes, give it the whole minute. If SE is still there afterward, schedule a visit.
The list is the keypad (user interface) or the wiring; testing on site settles it.
Tell us the model, the display wording and when SE first showed up.
Maytag codes, symptoms, parts and service
The Maytag page for Flashing ":" or PF in display on a over-the-range microwave states “There has been a power failure or the clock time has been turned off.” Nothing else is printed, so schedule a visit if it repeats.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
On a Maytag over-the-range microwave, SE, F2, F2E1 and E03 all point to the keypad, also called the user interface, or its wiring. Each page prints the same single step: cut power at the breaker for 60 seconds, restore it, wait a minute for a repeat, then run a cycle.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.