What it means
The Maytag page for Flashing ":" or PF in display on a over-the-range microwave states “There has been a power failure or the clock time has been turned off.” Nothing else is printed, so schedule a visit if it repeats.
Maytag microwave Flashing ":" or PF in display / Power supply
The Maytag page for Flashing ":" or PF in display on a over-the-range microwave states “There has been a power failure or the clock time has been turned off.” Nothing else is printed, so schedule a visit if it repeats.
Also printed as Flashing ":" or PF in display
The Maytag page for Flashing ":" or PF in display on a over-the-range microwave states “There has been a power failure or the clock time has been turned off.” Nothing else is printed, so schedule a visit if it repeats.
Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.
Flashing ":" or PF in display repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the microwave or switch off its breaker before any panel comes off, and never open the casing, because it holds charge.

Check that your appliance is an over-the-range microwave and copy Flashing ":" or PF in display exactly as the display shows it.

No reset is printed here; note the behavior of the microwave around Flashing ":" or PF in display instead.
Note the model and the moment Flashing ":" or PF in display showed up; both help us plan.
Ask whether Flashing ":" or PF in display is a mode someone switched on; Maytag describes it as a setting.
Note the model and the moment Flashing ":" or PF in display showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Here is what Maytag prints for Flashing ":" or PF in display on an over-the-range microwave: “There has been a power failure or the clock time has been turned off.”
Read the supporting manualMaytag's page for Flashing ":" or PF in display gives no reset or checking steps, so there is no page-approved first move beyond noting exactly what the microwave shows.
Read the supporting manualDoor or Open Door Closed is a neighbor of Flashing ":" or PF in display, not a synonym. The reset may overlap; the text does not.
Read the supporting manualNothing is wrong when Flashing ":" or PF in display is a mode message.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2023-08-16; PH 10326 / PH 10326 (over-the-range microwave)
Facts for Flashing ":" or PF in display are from the over-the-range microwave table (PH 10326) of Maytag Product Help, checked November 2026; no model list is printed.
The help page states “There has been a power failure or the clock time has been turned off.” Nothing else is added.
No; Maytag gives Flashing ":" or PF in display no reset steps. If it repeats, schedule a visit.
Nothing about replacing parts is printed for Flashing ":" or PF in display.
The model number, what Flashing ":" or PF in display looked like, and whether the reset changed anything.
Maytag codes, symptoms, parts and service
Door or Open Door Closed on a Maytag over-the-range microwave is explained as “This occurs to avoid unintended starting of the microwave oven.” Cut the power for five minutes, then restore it; schedule a visit if the code is still there.
If a Maytag microwave will not start, the display usually explains why: a door message, the LOC padlock icon, or Demo Mode. Reopen and reclose the door first, then check the lock and demo settings before you book a visit.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.