What it means
On a front-load washer, F5E3 means the door is not locking properly. Close it completely and clear the latch of clothing or shipping material, then reset for 5 minutes. The top-load page is headed Door Lock with a reset.
Maytag washer F5E3 / Door and lid
On a front-load washer, F5E3 means the door is not locking properly. Close it completely and clear the latch of clothing or shipping material, then reset for 5 minutes. The top-load page is headed Door Lock with a reset.
Also printed as F5E3
On a front-load washer, F5E3 means the door is not locking properly. Close it completely and clear the latch of clothing or shipping material, then reset for 5 minutes. The top-load page is headed Door Lock with a reset.
Power and water off before any panel comes off; towels down for spills.
F5E3 returns with the door closed and the latch clear.
Your Maytag to-do list, saved here on this device

Make sure it clicks shut.

Remove clothing or shipping materials from the latch area.

Unplug the washer for 5 minutes, or switch off its breaker for 5 minutes, then restore power.

Press and hold START/PAUSE for 2 to 5 seconds. [3]

A door that is stuck locked should be reported.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue.
Read the definitionIt is headed “F5 E3 Error Code - Door Lock” and says the door is not locking properly. It tells you to ensure the door is completely closed and nothing blocks the latch or prevents the door closing.
Read the supporting manualIt is headed “F5E3 Error Code: Door Lock” with the 5-minute reset and no further text.
Read the supporting manualF5E1 is the door switch code and names the switch.
Read the supporting manualThe manual lists a door not closed completely as the first reason the washer will not run.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14612 / PH 14612 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13444 / PH 13444 (top-load washer)
Manufacturer document
Maytag / Whirlpool Corporation (retailer copy of the Use & Care Guide, pdf.lowes.com)
W10254443A; PDF page numbers; retailer copy / PDF p. 18, Troubleshooting, “Washer will not run”
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14610 / PH 14610 (front-load washer)
The Product Help pages list no models, so the text applies to the washer type, not to a named model. Sources: Product Help PH 14612 (front-load), PH 13444 (top-load), PH 14610 and Use & Care Guide W10254443A page 18.
F5E3 is the lock, F5E1 the switch.
The page says the door is not locking properly and asks you to clear the latch first. It names no failed part.
5 minutes.
The page gives no extra text.
Maytag codes, symptoms, parts and service
For a front-load washer showing F5E2, Maytag prints “This error code indicates that the door is not locking properly.” Try the five-minute power-off reset, and schedule a visit if the code returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.