What it means
For a front-load washer showing F5E2, Maytag prints “This error code indicates that the door is not locking properly.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Maytag washer F5E2 / Door and lid
For a front-load washer showing F5E2, Maytag prints “This error code indicates that the door is not locking properly.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Also printed as F5E2
For a front-load washer showing F5E2, Maytag prints “This error code indicates that the door is not locking properly.” Try the five-minute power-off reset, and schedule a visit if the code returns.
Power and water off before any panel comes off; towels down for spills.
F5E2 will not clear after one proper reset.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the front-load washer list before you rely on the wording for F5E2.

Wait five minutes without power before you check for F5E2 again.

Run the washer briefly after the reset and see whether F5E2 comes back.

Open the door or lid of the front-load washer fully and close it again firmly; check nothing is caught in the seal or latch area.
Write down the model and serial numbers and the exact F5E2 wording before you call.
Give us the model and the checks you have run, then open your request right here.
Book a visitA rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.

Component reference
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue.
Read the definitionF5E2 is covered by this wording on the front-load washer page: “This error code indicates that the door is not locking properly.”
Read the supporting manualMaytag asks for five minutes without power. Wait the full time, restore power, and note whether F5E2 reappears.
Read the supporting manualF5E1 is a separate entry from F5E2 on the front-load washer page, with its own wording.
Read the supporting manualIf the door will not open, leave the front-load washer off and book us rather than prying. If F5E2 keeps returning, stop and schedule a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14611 / PH 14611 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 13443 / PH 13443 (top-load washer)
Facts for F5E2 are from the front-load washer table (PH 14611) of Maytag Product Help, checked November 2026; no model list is printed.
On the front-load washer page the line is “This error code indicates that the door is not locking properly.” No further cause is given.
Yes, run it as printed and schedule a visit if F5E2 stays.
Not by itself; the page stops at the line it prints.
The model and serial numbers, the exact display for F5E2, and what the front-load washer was doing at the time.
Maytag codes, symptoms, parts and service
F5E1 is a door switch code on both Maytag washer trees. Make sure the door is completely closed and nothing, such as clothing or shipping material, blocks the switch. Then reset for 5 minutes.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
On a Maytag front-load washer, F5E3 means the door is not locking properly and F22 is a front door lock issue. Product Help says to shut the door completely, clear anything from the latch, and wipe soap buildup off the lock. F5E1 names the door switch.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.