What it means
Maytag’s front-load washer page for F4E1 (PH 14608) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E1 returns.
Maytag washer F4E1 / Reset only
Maytag’s front-load washer page for F4E1 (PH 14608) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E1 returns.
Also printed as F4E1
Maytag’s front-load washer page for F4E1 (PH 14608) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E1 returns.
Power and water off before any panel comes off; towels down for spills.
F4E1 returns, or the front-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Power and water off before any panel comes off; towels down for spills.

Match the label on your appliance to the front-load washer list before you rely on the wording for F4E1.

Power off for five full minutes, then on, and look for F4E1.

Run the washer briefly after the reset and see whether F4E1 comes back.

Note whether the display, keys and lights of the front-load washer behave normally, or whether other odd things happen near F4E1.
Write down the model and serial numbers and the exact F4E1 wording before you call.
The dryer page ties this code to its heater system. The washer page prints no cause, so only the reset applies.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Nothing. The front-load washer page (PH 14608, modified November 2025) gives no cause, no part and no meaning for F4E1; it has only a power reset.
Read the supporting manualUnplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.
Read the supporting manualMaytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F4E1; if it is gone, run a short cycle and keep an eye on the washer.
Read the supporting manualGive us the model and serial numbers, the exact display, and what the washer was doing when F4E1 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.
Read the supporting manualYes, on its dryer page F4 E1 is headed Heater System, with a possible problem in the heater or heater relays. The over-the-range microwave page names the cavity temperature thermistor or its wiring.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14608 / PH 14608 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2026-08-19; PH 12810 / PH 12810 (dryer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10363 / PH 10363 (over-the-range microwave)
Facts for F4E1 come from Maytag Product Help, front-load washer page (PH 14608), read in November 2026. The pages list no models.
No. The front-load washer page prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.
Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.
Not in the sources we hold. We cite only the front-load washer page (PH 14608), so we describe F4E1 for front-load washers only.
Book a visit if F4E1 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.
Maytag does not say so for the washer. The dryer page names the heater or heater relays, but the washer page prints only a power reset and no cause.
Maytag codes, symptoms, parts and service
Maytag’s front-load washer page for F3E6 (PH 14607) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F3E6 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.