What it means
Maytag’s front-load washer page for F4E4 (PH 14609) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E4 returns.
Maytag washer F4E4 / Reset only
Maytag’s front-load washer page for F4E4 (PH 14609) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E4 returns.
Also printed as F4E4
Maytag’s front-load washer page for F4E4 (PH 14609) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E4 returns.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
F4E4 returns, or the front-load washer behaves oddly around the code.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Match the label on your appliance to the front-load washer list before you rely on the wording for F4E4.

Power off for five full minutes, then on, and look for F4E4.

Run the washer briefly after the reset and see whether F4E4 comes back.

Ask yourself whether a power cut, storm or cleaning cycle came just before F4E4.
Note the model and the moment F4E4 showed up; both help us plan.
The dryer page ties this code to line voltage. The washer page prints no cause, so only the reset applies to the washer.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Nothing. The front-load washer page (PH 14609, modified November 2025) gives no cause, no part and no meaning for F4E4; it has only a power reset.
Read the supporting manualUnplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.
Read the supporting manualMaytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F4E4; if it is gone, run a short cycle and keep an eye on the washer.
Read the supporting manualGive us the model and serial numbers, the exact display, and what the washer was doing when F4E4 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.
Read the supporting manualYes. The dryer page calls F4 E4 a Low or No Line Voltage diagnostic code, a possible problem with the home power supply keeping the heater from turning on. The over-the-range microwave page names the humidity thermistor or its wiring.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14609 / PH 14609 (front-load washer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-05-27; PH 12812 / PH 12812 (dryer)
Manufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2021-04-29; PH 10364 / PH 10364 (over-the-range microwave)
Facts for F4E4 come from Maytag Product Help, front-load washer page (PH 14609), read in November 2026. The pages list no models.
No. The front-load washer page prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.
Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.
Not in the sources we hold. We cite only the front-load washer page (PH 14609), so we describe F4E4 for front-load washers only.
Book a visit if F4E4 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.
Maytag does not say so for the washer. The dryer page mentions low or no line voltage, but the washer page prints only a power reset and no cause.
Maytag codes, symptoms, parts and service
Maytag’s front-load washer page for F4E1 (PH 14608) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F4E1 returns.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.