What it means
Maytag’s front-load washer page for F3E6 (PH 14607) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F3E6 returns.
Maytag washer F3E6 / Reset only
Maytag’s front-load washer page for F3E6 (PH 14607) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F3E6 returns.
Also printed as F3E6
Maytag’s front-load washer page for F3E6 (PH 14607) prints no meaning for the code, only a reset: cut power to the washer for five minutes, then restore it. Book a visit if F3E6 returns.
Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.
F3E6 repeats after the reset.
Your Maytag to-do list, saved here on this device

Unplug the machine or switch off its breaker before opening any panel, close the water taps, and keep floors dry so nobody slips.

Check that your appliance is a front-load washer and copy F3E6 exactly as the display shows it.

Wait five minutes without power before you check for F3E6 again.

Run the washer briefly after the reset and see whether F3E6 comes back.

The control board lives behind panels on the front-load washer; keep them closed.
Note the model and the moment F3E6 showed up; both help us plan.
Give us the model and the checks you have run, then open your request right here.
Book a visit
A rough sketch only, because a Maytag is laid out differently from model to model. Click a highlighted part to open its photo and the matching test.
Nothing. The front-load washer page (PH 14607, modified November 2025) gives no cause, no part and no meaning for F3E6; it has only a power reset.
Read the supporting manualUnplug the washer for 5 minutes and plug it back in, or switch its breaker off for 5 minutes and back on. Maytag compares it to restarting a computer.
Read the supporting manualMaytag says resetting the control can sometimes solve the issues you are experiencing, but it does not promise it. After the 5 minutes, watch the display for F3E6; if it is gone, run a short cycle and keep an eye on the washer.
Read the supporting manualGive us the model and serial numbers, the exact display, and what the washer was doing when F3E6 appeared. Say whether the reset cleared it, even for a short time, because a code that returns is the reason to book a visit.
Read the supporting manualManufacturer document
Maytag Product Help (producthelp.maytag.com)
dateModified 2025-11-19; PH 14607 / PH 14607 (front-load washer)
Facts for F3E6 come from Maytag Product Help, front-load washer page (PH 14607), read in November 2026. The pages list no models.
No. The front-load washer page prints only the reset instruction and no cause, so we cannot name a failed part and will not guess one.
Five minutes, as printed. Unplug the washer or switch off its breaker for the full 5 minutes before restoring power, because a shorter wait may not reset the control.
Not in the sources we hold. We cite only the front-load washer page (PH 14607), so we describe F3E6 for front-load washers only.
Book a visit if F3E6 returns after the 5-minute reset, or if the washer behaves oddly in other ways. Have the model and serial numbers ready.
Maytag codes, symptoms, parts and service
The Maytag page for F22 on a front-load washer states “F22 indicates a front door lock issue.” No reset is printed for it, so schedule a visit if it keeps appearing.
A Maytag washer that leaves water in the tub usually points to the drain setup before the machine itself: a hose pushed too far into the standpipe, a standpipe under 30 inches, tape sealing the hose, or a clogged drain pump filter. Check those first; if water still stays, book a technician.
Book a diagnostic for your model, done at the machine.
Office details, and the entry information to pass along.